APRILIA CAPONORD 1200 Service Station Manual Download Page 153

Page: 153 / 439

•

Potentiometer 1 and potentiometer 2 do not show a logical value: the sum of the two voltages

should be constant. The cause may be a malfunction in one of the two sensors or an ab-

normal resistance in one of the two circuits

Troubleshooting

•

Check the throttle body connector as well as the control unit connector. Check that cable

resistance between the throttle body connector (PIN 1) and the control unit (PIN 36) is a few

tenths of an Ohm. Check that cable resistance between the throttle body connector (PIN 4)

and the throttle control unit (PIN 21) is a few tenths of an Ohm. If one of the two is different,

restore the cable harness. If correct, replace the complete throttle body.

Front throttle Limp Home self-acquisition P0160

•

failed test

Error cause

•

Throttle position, kept by the springs, not within the expected range (at each key ON). The

instrument panel does not indicate the presence of this error even in the ATT status

Troubleshooting

•

Check if the throttle body and the intake duct are clean. If OK, replace the throttle body

Front throttle mechanical springs self-acquisition P0161

•

failed test

Error cause

•

Return time of the throttle, kept in position by the springs, not within the expected limits: the

causes can be a deterioration of the performance of the springs or excessive throttle friction

(at each key ON)

Troubleshooting

•

Check if the throttle body and the intake duct are clean. If OK, replace the throttle body

Front throttle minimum mechanical position self-acquisition P0162

•

failed test

Error cause

•

Position of the throttle stop not within the expected field (at each key ON)

Troubleshooting

•

Check if the throttle body and the intake duct are clean. If OK, replace the throttle body

Detection of the front throttle Recovery conditions (air temp., water temp.) P0163

•

possible presence of ice

Error cause

CAPONORD 1200

Electrical system

ELE SYS - 153

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands