APRILIA CAPONORD 1200 Service Station Manual Download Page 173

Page: 173 / 439

road surface and it adapts the calibration of the

suspension in real time in order to maximise com-

fort and keep the correct setup of the motorbike.

Level in electrical circuit diagram:

VCU (Vehicle Control Unit) control unit

Location:

•

On the vehicle: in the upper part from

the active fork leg (LH) of the fork.

•

Connector: on the component.

Pin out:

1. Ground from VCU

2. Temperature signal output

3. Supply from VCU

4. Pressure signal output

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

VCU ERRORS

Error pressure sensor shortcircuit C1407

Error cause

•

An excessive tension or a null tension has been detected on PIN A3 VCU.

Troubleshooting

•

Disconnect the connector of the sensor and check its insulation from ground and supply

system of PIN 4: if the insulation is not present, restore the cabling, otherwise replace the

sensor.

Error pressure sensor open circuit C1408

Error cause

•

An interruption of the circuit has been detected.

Troubleshooting

•

Check the connector on the component and the VCU connector. Disconnect the two con-

nectors and check the continuity of the cable between PIN 4 sensor and PIN A3 VCU and

restore the cable harness. If the cable harness is not damaged, replace the sensor.

Error temperature sensor shortcircuit C1409

Error cause

•

An excessive or null tension has been detected on PIN D1 VCU.

Troubleshooting

CAPONORD 1200

Electrical system

ELE SYS - 173

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands