APRILIA CAPONORD 1200 Service Station Manual Download Page 343 | Manualshive

Page: 343 / 439

background image

•

Move the vehicle forward so as to

check vertical oscillation of the chain in

other positions too. clearance should

remain constant at all wheel rotation

phases.

•

If clearance is uniform but over 30 mm

(1.18 in) or below 25 mm (0.98 in), ad-

justment is necessary.

ADJUSTMENT

CAUTION

GET A SPECIFIC REAR SERVICE STAND (OPT) TO AD-
JUST THE CHAIN.

If you need to adjust chain tension after the check:

•

Place the vehicle on its rear service

stand (OPT).

•

Loosen the nut (1) completely.

•

Loosen both lock nuts (4).

•

Actuate on the adjuster screws (5) and

adjust the chain clearance checking

that the references (2-3) match on both

sides of the vehicle.

•

Tighten both lock nuts (4).

•

Tighten the nut (1).

•

Check chain clearance.

CAUTION

TO ENSURE THAT THE WHEEL IS CORRECTLY CEN-
TRED, THERE ARE FIXED REFERENCE MARKINGS (2-3)
INSIDE THE CHAIN TENSIONER SLIDER SEATS ON THE
SWINGARMS, IN FRONT OF THE WHEEL AXLE.

CHECKING THE CHAIN, THE PINION AND THE SPROCKET FOR WEAR

Furthermore, check the following parts and make sure the chain, the pinion and the sprocket do not

show:

•

damaged rollers;

•

loosened pins;

•

dry, rusty, flattened or jammed chain links;

•

excessive wear;

•

missing sealing rings;

•

excessively worn or damaged pinion or sprocket teeth.

CAPONORD 1200

Chassis

CHAS - 343

«
...
341
342
343
344
345
...
»

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CAPONORD 1200

Easyrack 6622520 01 01

Brand: hepco & becker Pages: 4

Brand: KTM Pages: 29

Brand: Suzuki Pages: 89

Brand: Honda Pages: 140

Brand: Megelli Pages: 83

Brand: hepco & becker Pages: 2

Brand: Leatt Pages: 26

Brand: Leatt Pages: 26

Brand: Honda Pages: 153

CR125M Elsinore

Brand: Honda Pages: 64

Brand: Honda Pages: 202

Brand: Honda Pages: 160

Brand: Honda Pages: 148

CB UNICORN DAZZLER 2010

Brand: Honda Pages: 89

Brand: Honda Pages: 158

Brand: Honda Pages: 136

1986 GoldWing GL1200A

Brand: Honda Pages: 164

Brand: Honda Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands