Applied Biosystems 3500 User Manual Download Page 128

Page: 128 / 326

When a sequencing install standard run completes successfully, the CRL Pass/Fail

row displays green or red results.
For each capillary:

Click a capillary to display the spectral and raw data profiles for a capillary.

Check that the data meet the following criteria:

Attribute

Acceptance Criteria

Example

Order of the peaks in the spectral

profile (intensity vs pixel) from left to

right

4-dye: blue-green-yellow-red

Extraneous peaks in the raw data

profile (intensity vs scan)

None

Note:

The E5 profile may include

extraneous peaks outside the matrix

peak region, which can be ignored.

E5:

Extraneous peaks in the raw data

profile (intensity vs scan)

None

Peak morphology in the spectral

profile (intensity vs pixel)

• No gross overlaps, dips, or other

irregularities

• Peaks separate and distinct
• Peak apexes are separate and

distinct (the tails will overlap)

(Optional) Review the CRL Basepair Accuracy to determine discrepancies from

the reference sequence.
If you observe large discrepancies (for example, 5–10 contiguous miscalled bases

in the middle of a sequence), review the data. If you see a raw data peak larger

than the adjacent peaks with baseline pull-up in all 4-dye color channels, it may

indicate the presence of a bubble. Check the pump, run the Remove Bubbles

wizard (see “Remove bubbles from the polymer pump“ on page 237), then

repeat the run as needed.

If the data for the required number of capillaries meets the criteria above (at least

7 capillaries for 8-capillary instruments, at least 22 capillaries for 24-capillary

instruments), click Accept Results.

Evaluate

sequencing install

standard data

Chapter 6

Run calibrations and install checks

Run a Sequencing install check

128

3500/3500xL Genetic Analyzer User Guide—Data Collection Software v3.1

Summary of Contents for 3500







































































































































































































































































































































Search results

Summary of Contents for 3500

Reviews:

Related manuals for 3500

Brands by name

Popular brands

Applied Biosystems 3500, User Manual

Search results

Summary of Contents for 3500

Reviews:

Related manuals for 3500

Brands by name

Popular brands