Ametek Sorensen XG Operation Manual Download Page 262 | Manualshive

Page: 262 / 381

background image

Communications Options

6-52

M370430-01 Rev B

Table 6-1

LAN Setting Screens

LAN Parameter

Description

IP Address

Use the

SYST:COMM:LAN:ADDRess

command from a terminal to

change the address

To set a fixed ip address (i.e. 192.168.1.100) enter

SYST:COMM:LAN:ADDR “192.168.1.100”

Note that the IP address is placed in quotes.

To set the unit for DHCP mode enter

SYST:COMM:LAN:ADDR “0.0.0.0”

Note that this setting will not be made until either the power is cycled
or the

SYST:COMM:LAN:APPY

command is entered.

MAC Address

This  is  the  Media  Access  Control  address.    It  is  a  16  digit
hexadecimal value.  This number is unique to each device and may
not  be  changed  by  the  user.    It  is  visible  as  a  serial  tag  which  is
placed on the rear of the unit.

The MAC address may be displayed with the query command,

SYST:COMM:LAN:MACA?

Note:

If the MAC Address displayed is corrupted or does not match the

serial tag, there may have been a problem retrieving the LAN port
settings. This can happen if a static IP was set that conflicts with
another device on the network. To recover, turn on power to the unit
while holding down the SET key. This will allow the unit to boot without
attempting to collect the IP settings. You can then set the required IP
values. [See IP Address above].

GWAddress

Gateway address setting. A

default gateway

is a node (a router) on

a computer network that serves as an access point to another
network.
This value can be changed by using the command,

SYST:COMM:LAN:GWAD <address>

For example to set the gateway address to 192.168.1.1, use the
command

SYST:COMM:LAN:GWAD “192.168.1.1”

Any change to this value will NOT take effect until after power to the
unit has been cycled.

«
...
260
261
262
263
264
...
»

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Sorensen XG

Brand: Davey Water Products Pages: 4

ASCM18QM Series

Brand: Fein Pages: 20

PHLG 2000 SE - MANUEL 2

Brand: Parkside Pages: 30

Brand: Parkside Pages: 56

Brand: Parkside Pages: 53

Brand: Parkside Pages: 73

Brand: Parkside Pages: 20

PHLG 2000 SE - MANUEL 2

Brand: Parkside Pages: 5

Brand: Parkside Pages: 55

Brand: Parkside Pages: 10

Brand: Parkside Pages: 288

Brand: Parkside Pages: 74

Brand: Parkside Pages: 78

Brand: Parkside Pages: 35

Brand: Parkside Pages: 50

Brand: Parkside Pages: 41

Brand: Parkside Pages: 13

Brand: V-TAC Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands