Ametek Sorensen XG Operation Manual Download Page 328

Page: 328 / 381

-24

-01
R

I Co

nd
R
efe
re

nc
e

Table A-9

System Commands

Function

SCPI Command

Description

Parameter and
Range

Query

Set the menu
system
timeout

[:]SYSTem:FPANel[:TIMeout]

Sets the menu system
timeout.

<1–20 to one decimal
place seconds>

Yes

Resets the
Instrument to
default values.

[:]SYSTem[<channel>]:RESet

Resets all values to default
state (excluding calibration
data).

N/A

Wa it t o
Continue

[:]SYSTem[<channel>]:WAIT

Wait to continue command.

N/A

Self Test

[:]SYSTem[<channel>]:TEST?

Perform unit Self test,
returns 0 if pass, non zero
value for failure.

Yes

ID Query

[:]SYSTem[<channel>]:IDENtify

Query device ID string.

Yes

Save User
Preset

[:]SYSTem[<channel>]:SAVE

Save the user preset values.
Select any slot from 0-3.

Recall User
Preset
(previously
saved)

[:]SYSTem[<channel>]:RECall

Load the user preset values.
Select any slot from 0-3.

Query System
Error

[:]SYSTem[<channel>]:ERRor[:NEXT]?

Returns the next error in the
instrument’s error queue

Yes

Query System
Error Code

[:]SYSTem[<channel>]:ERRor:CODE[:NEXT]

Returns the error code only
for the next error in the
instrument’s error queue.

Yes

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Search results

Summary of Contents for Sorensen XG

Reviews:

Related manuals for Sorensen XG

Brands by name

Popular brands

Ametek Sorensen XG, Operation Manual

Search results

Summary of Contents for Sorensen XG

Reviews:

Related manuals for Sorensen XG

Brands by name

Popular brands