manualshive.com logo in svg

Ametek Sorensen XG, Operation Manual

Introducing the Ametek Sorensen XG, a cutting-edge power supply that guarantees unparalleled performance and reliability. Enhance your understanding and maximize your experience with this exceptional device by accessing the comprehensive Operation Manual available for free download at manualshive.com. Discover the power of the XG today!

Share
Download
background image

 
 
 

Safety

 

 

vi 

 

M370430-01 Rev B 

Standard Warnings 
 

 

 

WARNING: Keep these instructions 

This chapter contains important safety and operating instructions. Read and 
keep this Operating Manual for future reference. 

 

 

1.

 

Before installing and using the XG and XTR Family Programmable 
DC Power Supply, read all instructions and cautionary markings on 
the instrument and all appropriate sections of this Manual. 

2.

 

This instrument is for indoor use only. Do not expose the instrument 
to moisture. To reduce risk of fire hazard, do not cover or obstruct 
the ventilation openings. Be sure to install the instrument in a 
compartment which allows air to reach the ventilation inlets on the 
front and rear of the unit to prevent overheating. For more 
information, see “Ventilation” on page 2-4. 

3.

 

To avoid a risk of fire and electric shock, make sure that the existing 
wiring is in good condition and the wire is not undersized. Do not 
operate the instrument with damaged or substandard wiring. 

4.

 

Do not operate the instrument if it has received a sharp blow, been 
dropped, or otherwise damaged in any way. If the instrument is 
damaged, see the Warranty on page ii. 

5.

 

Do not disassemble the instrument. It contains no user-serviceable 
parts. See the Warranty on page ii for instructions on obtaining 
service. Attempting to service the  instrument yourself may result in 
a risk of electrical shock or fire. Internal capacitors remain charged 
after all power is disconnected. 

6.

 

To reduce the risk of electrical shock, disconnect AC power from 
the instrument before attempting any maintenance or cleaning or 
working on any circuits connected to the instrument. Turning off 
controls will not reduce this risk. 

 

 

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Sorensen XG

ODA EX Series Brochure & Operating Manual preview
EX Series
Brand: ODA Pages: 113
Hama Universal Notebook Power Supply Operating Instructions Manual preview
Universal Notebook Power Supply
Brand: Hama Pages: 24
Sanela SLZ 07 Mounting Instructions preview
SLZ 07
Brand: Sanela Pages: 2
Altronix AL125UL Manual preview
AL125UL
Brand: Altronix Pages: 4
Facom V.600R Instructions Manual preview
V.600R
Brand: Facom Pages: 35
Fein ASW 12-16 Operating Instructions Manual preview
ASW 12-16
Brand: Fein Pages: 95
Toolson 3909206958 Operating Manual preview
3909206958
Brand: Toolson Pages: 136
Whelen Engineering Company A490ATSC Installation Manual preview
A490ATSC
Brand: Whelen Engineering Company Pages: 2
Hander HJS-710-L User Manual preview
HJS-710-L
Brand: Hander Pages: 38
Espi V2-20A-150W-12V-1D User Manual preview
V2-20A-150W-12V-1D
Brand: Espi Pages: 32
Flair AT12H14 Instruction Manual preview
AT12H14
Brand: Flair Pages: 42
POWER USB WATCHDOG User Manual preview
WATCHDOG
Brand: POWER USB Pages: 9
Larzep EE25030-CE Instruction Manual preview
EE25030-CE
Brand: Larzep Pages: 13
KOBEO FS0150 Operator'S Manual preview
FS0150
Brand: KOBEO Pages: 6
Hitachi Koki RH600T Handling Instructions Manual preview
RH600T
Brand: Hitachi Koki Pages: 40
Hitachi Koki CN 16SA Handling Instructions Manual preview
CN 16SA
Brand: Hitachi Koki Pages: 44
Hitachi Koki WR 14DSL Handling Instructions Manual preview
WR 14DSL
Brand: Hitachi Koki Pages: 64
Hi-Spec DT40235 Owner'S Manual preview
DT40235
Brand: Hi-Spec Pages: 7

Brands by name

Popular brands

Load more brands