manualshive.com logo in svg

Ametek Sorensen XG, Operation Manual

Introducing the Ametek Sorensen XG, a cutting-edge power supply that guarantees unparalleled performance and reliability. Enhance your understanding and maximize your experience with this exceptional device by accessing the comprehensive Operation Manual available for free download at manualshive.com. Discover the power of the XG today!

Share
Download
background image

 
 
 

Local Operation 

 

M370430-01  Rev B 

3-19 

3 

Auxiliary Auto Start Mode

 

The Auxiliary Auto Start mode determines the state of the auxiliary 
output after a complete power cycle (all front panel LEDS are not 
illuminated). With Auxiliary Auto Start mode turned to On, the 
auxiliary output will be activated after the power supply is powered up 
again.

 

To define the Auxiliary Auto Start mode:

 

1.

 

Press and hold the OUTPUT ENABLE Aux button for 1 
second. 

 

or 

 is displayed.

 

2.

 

To change to status to On or Off, press the OUTPUT 
ENABLE Aux button.

 

The SCPI command (s) for these instructions are:

 

[:]OUTPut[<channel>]:AUXiliary:PowerON[:STATe]

 

Constant Power Mode 

(version 2.21 and higher) 

In

 

Constant Power Mode the power supply will continually adjust the 

current levels to maintain a constant power set point. This mode is 
intended primarily for loads with response time greater than 
approximately 100ms. In order to provide additional protection for the 
load, voltage and current limits may be set while in the constant power 
mode. If the unit cannot regulate to the Constant Power setting due to 
load conditions, it will regulate at either the voltage or the current limit 
depending on the load demand. 

Example, CP Mode: 

Constant Power set 500W 

Voltage limit 61V 

Current limit 20A 

 

To activate Constant Power mode and set the value: 

3.

 

Turn the 9-position mode control to the FLD position or press 
the rotary Adjust/Enter control if the 9-position mode control 
is already at the FLD position.

 

4.

 

Turn the rotary Adjust/Enter control until “



” is 

displayed.

 

5.

 

Press the rotary Adjust/Enter control.

 

6.

 

Turn the Adjust/Enter control to the desired set point.

 

7.

 

Press the rotary Adjust/Enter control 

 

8.

 

Turn the Adjust/Enter control control for fine adjustment.

 

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Sorensen XG

IBM S822LC Servicing preview
S822LC
Brand: IBM Pages: 146
IBM 9006-22C Installing And Configuring preview
9006-22C
Brand: IBM Pages: 148
Jet JDP-15M Operating Instructions Manual preview
JDP-15M
Brand: Jet Pages: 20
Jet JJ-8CS Owner'S Manual preview
JJ-8CS
Brand: Jet Pages: 28
Paslode CS200 Operating Manual And Schematic preview
CS200
Brand: Paslode Pages: 20
Valcom VP-6124-UPS Instruction Manual preview
VP-6124-UPS
Brand: Valcom Pages: 3
PS Audio Stellar PowerPlant 3 Owner'S Reference Manual preview
Stellar PowerPlant 3
Brand: PS Audio Pages: 20
Eaton Power Xpert Series Installation And Operation Manual preview
Power Xpert Series
Brand: Eaton Pages: 156
Parker PSSSE24A Installation & Service Instructions Manual preview
PSSSE24A
Brand: Parker Pages: 6
Happy Henhouse F15AC Instruction Manual preview
F15AC
Brand: Happy Henhouse Pages: 20
Tyco Electronics 525690 Instruction Sheet preview
525690
Brand: Tyco Electronics Pages: 8
Hantarex US 150 Installation Manual preview
US 150
Brand: Hantarex Pages: 24
MESTA UPS1000-83 Owner'S Manual preview
UPS1000-83
Brand: MESTA Pages: 26
probst SPEEDY VS-140 User Manual preview
SPEEDY VS-140
Brand: probst Pages: 28
Ametek Sorensen XPH Series Operation Manual preview
Sorensen XPH Series
Brand: Ametek Pages: 30
Conrad 3-in-1 PowerPack 2000 Operating Instructions preview
3-in-1 PowerPack 2000
Brand: Conrad Pages: 4
National All Day Battery Ride-On 7700 Instruction Manual preview
All Day Battery Ride-On 7700
Brand: National Pages: 89
Cornwell Tools CAT8000BP Operating Instructions preview
CAT8000BP
Brand: Cornwell Tools Pages: 4

Brands by name

Popular brands

Load more brands