manualshive.com logo in svg

Ametek Sorensen XG, Operation Manual

Introducing the Ametek Sorensen XG, a cutting-edge power supply that guarantees unparalleled performance and reliability. Enhance your understanding and maximize your experience with this exceptional device by accessing the comprehensive Operation Manual available for free download at manualshive.com. Discover the power of the XG today!

Share
Download
background image

 
 
 

Remote Operation 

 

M370430-01  Rev B 

5-75 

5 

Power Saving Control (Sleep Mode, XTR/XG 1700 W Only)

 

The Sleep Mode, supported by the XG/XTR family of DC power 
supplies, is an effective way to reduce overall power consumption when 
the power supply is not in use for a specified period of time.  If Sleep 
Mode is enabled, the power supply will revert to a low power 
consumption mode with the following characteristics: 

 

Display will be blank 

 

The internal cooling fans will run at the lowest possible speed for 

whisper quiet operation. 

 

Touching any button or one of the rotary knobs will immediately 

wake up the power supply to normal mode of operation. 

 

All settings will be preserved during sleep mode and the power 

supply will return to the previously set state when it wakes up. 

The following conditions must be met in order for Sleep Mode to 
engage: 

 

The output of the power supply and auxiliary outputs must be off 

(standby) 

 

The Sleep Mode must be enabled (on). 

To enable Sleep Mode: 

Set a time delay for the duration of inactivity to elapse before entering 
Sleep Mode. This time (sleep hold-off delay) can be set from the 
Protection menu, under the SLP entry. The sleep hold off delay can be 
set from 1 to 24 hours. 

To disable the Sleep Mode: 

Set the sleep hold off delay value to zero (0).  This is also the default 
state for the Sleep Mode feature. Thus, unless set from the front panel or 
remotely using a SCPI command, Sleep Mode is off. Once enabled (set 
to a value from 1 to 24), it will be enabled. If the set time elapses without 
any activity on the power supply, it will enter Sleep Mode. 

Note that after issuing a *RST command, the power supply will revert to 
factory default settings which means Sleep Mode will be turned off. 

Command: 

[:]SYSTem[<channel>]:PROTection:SLEep <sleep_time> 

Query Format: 

[:]SYSTem[<channel>]:PROTection:SLEep? 

 
 

 

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Sorensen XG

Makita BHS630 Technical Information preview
BHS630
Brand: Makita Pages: 16
Quasar 3125 Quick Start Manual preview
3125
Brand: Quasar Pages: 3
tams elektronik BiDi-Power Series Manual preview
BiDi-Power Series
Brand: tams elektronik Pages: 16
KEPCO HSF-1UR Series Quick Start Manual preview
HSF-1UR Series
Brand: KEPCO Pages: 2
Caillau Clic Instruction Manual preview
Clic
Brand: Caillau Pages: 14
Stanley PROSET PB2500 Instruction Manual preview
PROSET PB2500
Brand: Stanley Pages: 233
MacAllister MTC500 Manual preview
MTC500
Brand: MacAllister Pages: 37
Intec Controls I-PS24 Installation & Operation Instructions preview
I-PS24
Brand: Intec Controls Pages: 3
Narex ASR 14 ES Original Operating Manual preview
ASR 14 ES
Brand: Narex Pages: 32
mxr Mini Iso-Brick M239 User Manual preview
Mini Iso-Brick M239
Brand: mxr Pages: 5
DIS PS 6000 User Manual preview
PS 6000
Brand: DIS Pages: 14
Wacker Neuson BH23 Operator'S Manual preview
BH23
Brand: Wacker Neuson Pages: 68
Hama D3 223851 Operating Instructions Manual preview
D3 223851
Brand: Hama Pages: 8
Scame LIBERA 204.W Series Quick Start Manual preview
LIBERA 204.W Series
Brand: Scame Pages: 4
TE Connectivity 2216055 Customer'S Manual preview
2216055
Brand: TE Connectivity Pages: 92
TDK-Lambda 802 Series Operator'S Manual preview
802 Series
Brand: TDK-Lambda Pages: 71
Rockwell Automation Allen-Bradley 1606-XLB90EQ Installation Instructions preview
Allen-Bradley 1606-XLB90EQ
Brand: Rockwell Automation Pages: 2
Rockwell Automation Allen-Bradley 1606-XLE240E-3 Reference Manual preview
Allen-Bradley 1606-XLE240E-3
Brand: Rockwell Automation Pages: 34

Brands by name

Popular brands

Load more brands