Ametek Sorensen XG Operation Manual Download Page 299

Page: 299 / 381

Calibration and Troubleshooting

M370430-01 Rev B

7-23

For example, you would type

CAL:

INP

ANAL:

CURR

if you read 0.43 volts from the voltmeter.

After performing offset calibration, it is highly recommended that
you repeat gain calibration.

SCPI Command

[:]CALibration[<channel>]:INPut:ANALog[:VOLTage]
{<voltmeter reading in volts>}

Calibrating the Input Current APG Signal

The input voltage APG calibration is necessary to ensure accurate
measurements when using the

:MEAS : APR?

and

:MEAS : APR: ISOL?

SCPI command queries to monitor the APG input signal.

Gain Calibration

To calibrate the CAP APG input gain calibration:

Connect a short across the power supply output.

Connect a voltmeter and a DC voltage source to the

non-isolated current APG input lines (J1. 10 and J1 .7).

Turn the power supply On.

Set the Current APG level to 4 V. Send the SCPI command:

SYST:COMM:APR:LEV:CURR 4

Set the input source as Voltage analog APG. Send the SCPI

command:

SYST:REM:

SOUR:

CURR

AVOL

Set the voltage source attached to the non-isolated current

APG input to 90% of the nominal current level, in this case
3.6 V.

Turn the output power on.

The power supply starts up in Constant Current mode.

Read the input voltage value from the voltmeter connected in

step 2.

10.

Type the SCPI input current calibration command with

voltage noted in step 9 as the parameter “data”.

For example, you would type : CAL: INP: ANAL: CURR 3.49 if
you were reading 3.49 volts from the voltmeter.

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Search results

Summary of Contents for Sorensen XG

Reviews:

Related manuals for Sorensen XG

Brands by name

Popular brands

Ametek Sorensen XG, Operation Manual

Search results

Summary of Contents for Sorensen XG

Reviews:

Related manuals for Sorensen XG

Brands by name

Popular brands