Ametek Sorensen XG Operation Manual Download Page 153 | Manualshive

Page: 153 / 381

background image

Remote Operation

M370430-01 Rev B

5-19

5

Ethernet/LAN (ENET) Connector (Optional)

The power supply also can be programmed from a remote terminal
using the Ethernet (ENET). If your power supply is configured with the
Ethernet option, set-up instructions differ between the 850 Watt models
and the 1500 and 1700 Watt models.

For the

XG/XTR 850 Watt

power supply with the MEA option, see

SETTING UP XG/XTR 850 WATT MODELS in Section 6
“Communications Options” of this manual

).

Note the the MEA option

instructions in the manual are for reference only. The MEA option is no
longer available.

For the

XG/XTR 1500 and 1700 Watt

power supplies with the MEB

option, see SETTING UP XG/XTR 1500 and 1700 WATT MODELS in
Section 6 “Communications Options” of this manual.

For connecting the power supply to ENET, use a LAN RJ-45 and RJ-45
STP. Use a standard RJ-45 and RJ-45 cross-cable, Cat 5.

Multiple Power Supply Connections to RS-485 Bus

Up to 30 units may be connected to the RS-485 bus. The first unit
(master unit) connects to the controller via any appropriate port, and the
other units (slave units) are connected with the RS-485 bus via the J6
connector. All units connected together should also have unique
multichannel addresses.

A standard straight-through RJ-45 Ethernet network cable can be used to
provide the connection between the power supplies. See Figure 5-13.

Figure 5-15

Multi Power Supply Connection to RS-485 Bus

IN

OUT

IN

OUT

IN

OUT

Power Supply #1

Power Supply #2

Power Supply #30

«
...
151
152
153
154
155
...
»

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Sorensen XG

Brand: Oasser Pages: 29

Brand: Gallagher Pages: 98

Brand: Daxten Pages: 2

Brand: MAC TOOLS Pages: 44

Brand: Elmdene Pages: 8

Brand: Delta Elektronika Pages: 30

Brand: NETGEAR Pages: 11

COMFORT CRIMP TBM21E

Brand: Thomas & Betts Pages: 2

Brand: IDX Pages: 7

TrakFast TF1100

Brand: RAMSET Pages: 18

Brand: Celltronix Pages: 10

Wi-Fi Anywhere PTE2700

Brand: JVA Pages: 8

Brand: Monoprice Pages: 9

Brand: Rebel Pages: 2

Brand: Malibu Boats Pages: 2

Brand: Altronix Pages: 2

Sorensen XPH Series

Brand: Ametek Pages: 30

3-in-1 PowerPack 2000

Brand: Conrad Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands