manualshive.com logo in svg

Ametek Sorensen XG, Operation Manual

Introducing the Ametek Sorensen XG, a cutting-edge power supply that guarantees unparalleled performance and reliability. Enhance your understanding and maximize your experience with this exceptional device by accessing the comprehensive Operation Manual available for free download at manualshive.com. Discover the power of the XG today!

Share
Download
background image

 
 
 

Communications Options 

 

6-62 

M370430-01  Rev B 

NCON  parameter  (Network  Connection  Setting)  must  be  added  to  the  query.  The 
default value is 8. In general Class A network is 24 bits, Class B is 16 bits and Class A 
is 8 bits. 

Command Syntax 

SYSTem:COMMunicate:LAN:CLASs <NRF> 

Parameters 

8 to 32 

Example 

SYST:COMM:LAN:CLAS 8 

Query Syntax 

SYST:COMM:LAN: CLAS? 

 

SYST:COMM:LAN: CLAS? NCON 

Returned Parameters 

<NR1> 

SYSTem:COMMunicate:LAN:DEFault 

This  command  will  apply  the  changes  in  LAN  setting  to  the  default  setting.  The 
controller will go to reset condition and the default LAN setting will take effect. Both IP 
address  and  Gate  way  address  are  set  to  zero.  The  Host  name  is  cleared.  The 
password is reset to “admin”The unit is set to DHCP or Auto IP. 

Command Syntax 

SYSTem:COMMunicate:LAN:DEFault 

Parameters 

none 

Example 

SYST:COMM:LAN:DEF  

Query Syntax 

no query for this command 

Returned Parameters 

none 

SYSTem:COMMunicate:LAN:DESCription 

This command will set the user description. The description is limited to 24 characters 

Command Syntax 

SYSTem:COMMunicate:LAN:DESCription <SRD> 

Parameters 

<SRD> 

Example 

SYST:COMM:LAN:DESC “EVAL UNIT”  

Query Syntax 

SYST:COMM:LAN:DESC? 

Returned Parameters 

<SRD> 

SYSTem:COMMunicate:LAN:GWADdress 

This  command  will  set  the  LAN  Gateway  address.  The  query  format  returns  the 
Gateway address set. To query the actual gateway address used by the LAN interface 
(in  case  the  IP  address  is  not  static  but  assigned  by  a  DHCP  server),  the  NCON 
parameter  (Network  Connection  Setting)  must  be  added  to  the  query.  The  default 
value is 0.0.0.0. 

Command Syntax 

SYSTem:COMMunicate:LAN:GWADddress <NRF> 

Parameters 

ddd.ddd.ddd.ddd <Gateway address> 

Example 

SYST:COMM:LAN:GWAD 255.255.255.0  

Query Syntax 

SYST:COMM:LAN:GWAD? 

 

SYST:COMM:LAN:GWAD? NCON 

Returned Parameters 

<CRD> 

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Sorensen XG

Ametek Sorensen XG 100-15 Operating Manual preview
Sorensen XG 100-15
Brand: Ametek Pages: 399
SIP rescue pac 1600 Instruction Manual preview
rescue pac 1600
Brand: SIP Pages: 6
GEM PSU320-12 Manual preview
PSU320-12
Brand: GEM Pages: 2
Fein ASCS4.8 User Manual preview
ASCS4.8
Brand: Fein Pages: 125
Textron Greenlee INLNPRESS-TOOL19kN Operation Manual preview
Greenlee INLNPRESS-TOOL19kN
Brand: Textron Pages: 12
Xinpu XP-G80BE Handling Instructions Manual preview
XP-G80BE
Brand: Xinpu Pages: 12
Central Pneumatic Central Pneumatic 1/4" Stubby Air Ratchet 91002 Operating Instructions Manual preview
Central Pneumatic 1/4" Stubby Air Ratchet 91002
Brand: Central Pneumatic Pages: 8
Elektro-Automatik PSI 9000 WR 3U SLAVE Operating Manual preview
PSI 9000 WR 3U SLAVE
Brand: Elektro-Automatik Pages: 44
IDX WR88 Quick Start Manual preview
WR88
Brand: IDX Pages: 7
RAMSET TrakFast TF1100 Operating Instructions Manual preview
TrakFast TF1100
Brand: RAMSET Pages: 18
Parkside 332006 1907 Instructions Manual preview
332006 1907
Brand: Parkside Pages: 94
Parkside 286098 Translation Of The Original Instructions preview
286098
Brand: Parkside Pages: 109
Puls CS10.244 Installation Manual preview
CS10.244
Brand: Puls Pages: 2
Dake 75H Instructional Manual preview
75H
Brand: Dake Pages: 17
PTN TPUH-PSU12 User Manual preview
TPUH-PSU12
Brand: PTN Pages: 24
Eastwood 13650 Instructions preview
13650
Brand: Eastwood Pages: 3
Campbell Hausfeld SN268K00 Operating Instructions Manual preview
SN268K00
Brand: Campbell Hausfeld Pages: 12
nextys NUPS12 Instruction Manual preview
NUPS12
Brand: nextys Pages: 5

Brands by name

Popular brands

Load more brands