manualshive.com logo in svg

Ametek Sorensen XG, Operation Manual

Introducing the Ametek Sorensen XG, a cutting-edge power supply that guarantees unparalleled performance and reliability. Enhance your understanding and maximize your experience with this exceptional device by accessing the comprehensive Operation Manual available for free download at manualshive.com. Discover the power of the XG today!

Share
Download
background image

 
 
 

Communications Options 

 

M370430-01  Rev B 

6-61 

6 

SYSTEM COMMANDS 

The system commands control the system-level functions of the 
power source. 

Subsystem Syntax

 

SYSTem 
      :COMMunicate 
          :LAN 
              :ADDRess 

 

Set LAN IP address 

              :APPLy 

 

Apply the change in setting 

              :CLASs 

 

Set LAN Host bits 

              :DEFault 

 

Set  LAN  to  a  default  known 

setting 

              :DESCription 

 

Set user description 

              :DNSaddress 

 

Set LAN DNS address 

              :GWADdress 

 

Set LAN Gateway 

              :PASSword 

 

Set LAN password 

              :PORT 

 

Set LAN socket port address 

              :MACAddress 

 

Read the MAC address 

 

SYSTem:COMMunicate:LAN:ADDRess 

This command will set the LAN IP address. The query format returns the IP address 
set. To query the actual IP address used by the LAN interface (in case the IP address 
is  not  static  but  assigned  by  a  DHCP  server),  the  NCON  parameter  (Network 
Connection Setting) must be added to the query. The default value is 0.0.0.0. 

Command Syntax 

SYSTem:COMMunicate:LAN:ADDRess <NRF> 

Parameters 

ddd.ddd.ddd.ddd <IP address> 

Example 

SYST:COMM:LAN:ADDR 255.255.167.2  

Query Syntax 

SYST:COMM:LAN:ADDR? 

 

SYST:COMM:LAN:ADDR? NCON 

Returned Parameters 

<CRD> 

 

SYSTem:COMMunicate:LAN:APPLy 

This  command  will  apply  the  changes  in  LAN  setting.  The  controller  will  go  to  reset 
condition and the new LAN setting will take effect. 

Command Syntax 

SYSTem:COMMunicate:LAN:APPLy 

Parameters 

none 

Example 

SYST:COMM:LAN:APPL  

Query Syntax 

no query for this command 

Returned Parameters 

none 

SYSTem:COMMunicate:LAN:CLASs 

This command will set the number of host address bits or a class. The query format 
returns the number of bits  set. To query  the  actual number of bits used by  the LAN 
interface  (in  case  the  IP  address  is  not  static  but  assigned  by  a  DHCP  server),  the 

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Sorensen XG

Harley Benton Powerplant Owner'S Manual preview
Powerplant
Brand: Harley Benton Pages: 16
Badger Welder B22 Operation Manual preview
B22
Brand: Badger Welder Pages: 6
Makita DDA341 Original Instructions Manual preview
DDA341
Brand: Makita Pages: 11
Makita HM1810 Quick Start Manual preview
HM1810
Brand: Makita Pages: 4
Makita HM0810T Instructions Manual preview
HM0810T
Brand: Makita Pages: 8
Emcore 10901G Operator'S Manual preview
10901G
Brand: Emcore Pages: 13
Baileigh Industrial HSP-176M-1500-HD Operator'S Manual preview
HSP-176M-1500-HD
Brand: Baileigh Industrial Pages: 44
Würth 1952 003 133 Translation Of The Original Operating Instructions preview
1952 003 133
Brand: Würth Pages: 8
Ryobi ERT-1150VN Owner'S Manual preview
ERT-1150VN
Brand: Ryobi Pages: 15
Koch PxtRX Operating Manual preview
PxtRX
Brand: Koch Pages: 76
Wacker Neuson VP1340A US Operator'S Manual preview
VP1340A US
Brand: Wacker Neuson Pages: 32
Matco Tools MT1857 Manual preview
MT1857
Brand: Matco Tools Pages: 10
BRICK MPV2200-75 Original Instructions Manual preview
MPV2200-75
Brand: BRICK Pages: 30
X-Tronic 6040-XTS Instructions Manual preview
6040-XTS
Brand: X-Tronic Pages: 8
MGC PS-2040 Installation Instructions preview
PS-2040
Brand: MGC Pages: 2
Goobay 4040849511912 User Manual preview
4040849511912
Brand: Goobay Pages: 10
Chicago Pneumatic CP782 Operator'S Manual preview
CP782
Brand: Chicago Pneumatic Pages: 3
Hilti TE3000-AVR Safety Sheet preview
TE3000-AVR
Brand: Hilti Pages: 2

Brands by name

Popular brands

Load more brands