Ametek Sorensen XG Operation Manual Download Page 283

Page: 283 / 381

Calibration and Troubleshooting

M370430-01 Rev B

7-7

After performing offset calibration, it is recommended that you repeat
gain calibration.

Important:

For best results, both calibrations may be repeated several times.

The SCPI Command (s) for these instructions are:

[:]CALibration[<channel>]:OUTPut{:VOLTage]{<voltmeter
reading in volts>}

Calibrating the Output Current

Gain Calibration

To perform gain calibration:

Disconnect the power supply from the load.

Connect the output terminals to a load representing a short

circuit using a precision ammeter.

Turn both the power supply and the load On.

Set the voltage set point to maximum. Set the supply output to

90% of the nominal current level.

Turn on the output power.

The power supply starts up in Constant Current mode.

Read the current value on the ammeter display.

Type SCPI command with current value as parameter “data”.

For example, type

: CAL: OUTP 5.07

if you had an XG (or XTR)

150-5.6 calibrating with the current set point set to 5.04 A and the
ammeter was reading 5.07 amps.

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Search results

Summary of Contents for Sorensen XG

Reviews:

Related manuals for Sorensen XG

Brands by name

Popular brands

Ametek Sorensen XG, Operation Manual

Search results

Summary of Contents for Sorensen XG

Reviews:

Related manuals for Sorensen XG

Brands by name

Popular brands