Ametek Sorensen XG Operation Manual Download Page 351 | Manualshive

Page: 351 / 381

background image

Sp
e

c

ifi

c

a

ti

o

n

s

M

37
0

43
0

-01
R

ev
B

C

-5

C

Table C-2

XG/XTR 1500 Watt Electrical Specifications for 6 V to 600 V Models

Models

6-220

8-187.5

12.5-120

20-76

30-50

40-38

60-25

80-19

100-15

150-10

300-5

600-2.6

Efficiency

11

75/77%

77/80%

79.5/
82.5%

82/85%

83/86%

83/87%

83/87%

83/87%

83/87%

83/87%

83/87%

83/87%

1. Maximum output voltage is guaranteed to be ≤ 0.1% of the rated voltage at zero output setting, using the front panel or digital remote programming modes.
2. Maximum output current is guaranteed to be ≤ 0.2% of the rated current at zero output setting, using the front panel or digital remote programming modes, and when measured with rated
load resistance.
3. Total output power doesn’t include AUX1 Output Voltage (5 V) and AUX1 Output Current (0.5 A) and AUX2 Output Voltage (15 V) and AUX2 Output Current (0.5 A).
4. From 90–132 Vac or 170–265 Vac, constant load.
5. From 90–132 Vac or 170–265 Vac, constant load.
6. From no load to full load, constant input voltage.
7. For load voltage change, equal to the unit voltage rating, constant input voltage.
8. For 6 V models the current ripple is measured at 2–6 V output voltage and full output current. For all other models, the current ripple is measured at 10–100% output voltage and full output
current.
9. When using remote sense, the total of the load voltage and the load line drops must not exceed the rated output of the power supply. For example, for an XG 6-220 in an application with
1 V of load line loss (0.5 V/Line), the maximum available load voltage would be 6–1= 5 V. Note: The unit may operate at higher output voltages than this, but there is no guarantee that the
power supply will meet performance specifications. Ultimately, the upper limit of the output voltage will be determined by internal circuitry of the power supply (non-adjustable.)
10. With rated, resistive load.
11. At 100/200 Vac input voltage and maximum output power.
Applies to all footnotes: Programming and Readback: RS-232, RS-485, USB built in. GPIB, Ethernet optional.
Specifications are guaranteed from 1% to 100% of the rated output voltage, current, and power.

AC Line Input Specifications for XG/XTR 1500 Watt

The input to the power supply requires the following input specifications.

Rated AC Input Voltage/Frequency

100–240 Vac, 47–63 Hz

Operational AC Input Voltage/Frequency

85–265 Vac continuous, single phase, 360-440 Hz*, 47–63 Hz, single phase

Input Current (at 100/200 Vac)

23/12 A

Inrush Current (100/200 Vac)

Less than 50 A

Power Factor Correction

0.99@100/200 Vac, rated output power

*

Contact factory for details regarding this mode of operation.

«
...
349
350
351
352
353
...
»

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Sorensen XG

BT-CK 18 2B-1.5 Kit

Brand: Taurus Pages: 40

EHR 20 / 2.6 S SET

Brand: EIBENSTOCK Pages: 64

Brand: Parkside Pages: 64

Brand: Parkside Pages: 19

Emberstrip ESUSAV8-ET-10D

Brand: Embertec Pages: 21

Brand: X-Tronic Pages: 12

Brand: G-Scale Graphics Pages: 4

GE current Tetra GEPS24-100U-GLX

Brand: Daintree Pages: 3

Brand: Cantek Pages: 29

Brand: Cleco Pages: 38

Brand: HIKOKI Pages: 196

Brand: Parkside Pages: 50

Brand: TDK-Lambda Pages: 11

Brand: Napa Pages: 12

Brand: BBT Pages: 18

Brand: Kilews Pages: 14

Brand: Band-it Pages: 4

Brand: Chicago Pneumatic Pages: 196

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands