manualshive.com logo in svg

Ametek Sorensen XG, Operation Manual

Introducing the Ametek Sorensen XG, a cutting-edge power supply that guarantees unparalleled performance and reliability. Enhance your understanding and maximize your experience with this exceptional device by accessing the comprehensive Operation Manual available for free download at manualshive.com. Discover the power of the XG today!

Share
Download
background image

 
 
 

Communications Options 

 

6-32 

M370430-01  Rev B 

SETTING UP XG/XTR 1500 and 1700 WATT 
MODELS 

This section is intended for network administrators responsible for 
the configuration and maintenance of devices on the network. It 
provides information for connecting and configuring the power 
supply with the MEB option. 

LOCAL AREA NETWORK (LAN) OPTION 

All power supplies functions are programmable over the LAN 
(Ethernet) interface if the ENET/LAN option is installed (specified 
at the time of order) The ENET/LAN interface, which operates 
with auto detection, supports 10Base-T, 100Base-T and 
1000Base-T. 

Using LAN allows remote communication with the instrument; it 
is fast, simple and the LAN from your PC does not require any 
additional proprietary software or cards. 

Media Access Control (MAC) Address 

Each power source with the LAN option installed has a unique 
network address known as the MAC address, a unique 
hexadecimal address, which is listed on a rear panel label of the 
power source.  To operate the power source on a network, this 
MAC address needs to be assigned to a TCP/IP address, which will 
be used to address the device on the network. 

Communication Configuration 

Presented here are three connection choices for remote control of 
the instrument: 

 

through a local area network (LAN) 

 

direct to a PC 

 

through a private network. 

Each requires an IP address; the LAN also requires a Gateway 
address. The addresses can be set automatically through a 
Dynamic Host Configuration Protocol (DHCP) server or set 
manually with a static IP address. 

LAN Connection 

Connect the instrument directly to a network Ethernet port with a 
LAN cable, and allow the DHCP server to automatically assign a 
dynamic IP and Gateway address. If DHCP is not enabled, see the 
section on SETTING LAN PARAMETERS

 

in this chapter or 

contact your network administrator. 

Summary of Contents for Sorensen XG






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Sorensen XG

JAMEC PEM TDR3000 Instruction Manual preview
TDR3000
Brand: JAMEC PEM Pages: 4
Dake TB-16 Instructional Manual preview
TB-16
Brand: Dake Pages: 24
Westfalia 83 58 98 Instruction Manual preview
83 58 98
Brand: Westfalia Pages: 18
Parkside 3041 Operation And Safety Notes preview
3041
Brand: Parkside Pages: 37
YATO YT-82902 Original Instructions Manual preview
YT-82902
Brand: YATO Pages: 80
Fein ASCS4.8 User Manual preview
ASCS4.8
Brand: Fein Pages: 125
Textron Greenlee INLNPRESS-TOOL19kN Operation Manual preview
Greenlee INLNPRESS-TOOL19kN
Brand: Textron Pages: 12
Hakko Electronics FT-8004 Instruction Manual preview
FT-8004
Brand: Hakko Electronics Pages: 2
Energenie EG-PMSU User Manual preview
EG-PMSU
Brand: Energenie Pages: 45
IDX WR88 Quick Start Manual preview
WR88
Brand: IDX Pages: 7
RAMSET TrakFast TF1100 Operating Instructions Manual preview
TrakFast TF1100
Brand: RAMSET Pages: 18
AEMC AX501 User Manual preview
AX501
Brand: AEMC Pages: 24
Omer 90.38 CLD2-3 Use, Maintenance And Spare Parts Manual preview
90.38 CLD2-3
Brand: Omer Pages: 2
ECO POWER SBP-XFMR Series Installation And User Instructions Manual preview
SBP-XFMR Series
Brand: ECO POWER Pages: 21
SNOWJOE sunjoe24V-HG100 Operator'S Manual preview
sunjoe24V-HG100
Brand: SNOWJOE Pages: 52
P.I.T. PMT20H-035A User Manual preview
PMT20H-035A
Brand: P.I.T. Pages: 24
Xantrex XPH 35-5 Operating Manual preview
XPH 35-5
Brand: Xantrex Pages: 31
Leister WELDPLAST S4 Operating Instructions Manual preview
WELDPLAST S4
Brand: Leister Pages: 60

Brands by name

Popular brands

Load more brands