manualshive.com logo in svg

Amano MX-300, Operation Manual, Page: 17 / 90

Share
Download
Amano MX-300 Operation Manual Download Page 17

11 

 

When an Overtime Beginning Time is configured, the time 
from the corresponding start time to a minute prior to Day 
Change Time is treated as an Overtime Zone. 
If the Overtime Beginning Time is set to a time other than the 
Shift End Time, then the time between the two is treated as 
break time. 

 
 
 

When a Midnight Shift Beginning and End time is 

configured, the corresponding time zone is treated as a 

Midnight Time Zone and is the corresponding hours 

worked during that time is calculated separately from 

overtime hours in the monthly totals. (The daily totals 

for both overtime and midnight hours are printed as one 

total.)  

   
 
 

 

 
 

When you finish configuring the Midnight Shift Time Zone 
the programming card is ejected. 
Next, turn the card over the back side to insert 
PROGRAMMING CARD FOR REGULAR EMPLOYEES #4. 

 

 

You can configure up to four scheduled ("fixed") breaks 

a day for regular employees. The time zone for a given 

break is determined by the Fixed Break Beginning and 

End Time. 

* You may not configure breaks so that they run back to back 

or overlap each other! 

NG

                                                       

NG

 

 

 

* Also, you may not configure breaks so that they overlap 

Shift Beginning and End Times. 



 The following setting is a detail example of page 22's 

"How to Change the Calculation Mode" when selecting the 
option for hourly workers. The settings are only valid for 
the type of hourly worker selected. 

 

Overtime Beginning Time 

 

Not configured 

Factory Setting 

Configure

 

Don't 
configure

"How to Adjust 

the Overtime 

Beginning Time"

 

Go to Page 30

 

Example: Overtime Beginning Time: 17:30

Regular Hours Time Zone

5

6

7

8

9

10 11 12 13

19 20 21

14 15 16 17

2

3

4

Overtime Zone

22 23 24 1

18

Day Change Time

Overtime Beginning

Time

Break Time

Shift

Beginning

Time

Shift End

Time

Midnight Time Zone 

 

Not configured 

Factory

 Setting

 

Configure

 

"How to Adjust 

the Midnight Shift 

Time Zone"

 

Go to Page 31

 

Example: Midnight Shift Time Zone: 22:00 to 4:00

Midnight Shift Time Zone

Overtime Zone

Day Change Time

4

19

1

2

3

21 22 23 24

17 18

20

13 14 15 16

9

10 11 12

5

6

7

8

Regular Hours Time Zone

Overtime Zone

Break Time

Overtime

Beginning Time

Shift

Beginning

Time

Shift End

Time

Midnight Shift

Beginning Time

Midnight Shift

End Time

Breaks for Regular Employees

Configure

 

"How to Configure 
Breaks for Regular 
Employees" 

Go to Page 32

 

#1 Fixed 
Break  

#2 Fixed 
Break 

#1 

Fixed 

Break 

#2 

Fixed 

Break

Press Next 

(button 

h

)

Press Next 

(button 

h

)

Hourly Worker with Fixed Shift 

Ö

 Page 12

Hourly Worker with Open Shift

Ö

 Page 14

 

Not configured 

Factory

 Setting

 

PROGRAMMING CARD FOR 
REGULAR EMPLOYEES #3 is 
ejected. 

Insert PROGRAMMING CARD 
FOR REGULAR EMPLOYEES #4

PROGRAMMING CARD FOR REGULAR 
EMPLOYEES #4 is ejected. 

Day Change Time 

minus 1 minute 

Day Change Time minus 

1 minute 

Don't 
configure

 

Don't 
configure

 

Press Next
(button 

h

)

four times

HOURLY WORKERS 
WITH FIXED SHIFT

 

HOURLY WORKERS 
WITH OPEN SHIFT 

Go to "How to Change the Calculation 
Mode"  

Ö

 Page 22 

Summary of Contents for MX-300



























































































Reviews:

No comments