manualshive.com logo in svg

Allen-Bradley Kinetix 5100 2198-E1004-ERS, User Manual, Page: 420 / 500

Share
Download
Allen-Bradley Kinetix 5100 2198-E1004-ERS User Manual Download Page 420

420

Rockwell Automation Publication 2198-UM004A-EN-P - October 2019

Chapter 15

Programming via Drive Parameters

019 (13h)

Mapping parameter 

content #1

B, DEC

Returns the value of P0.025, which is mapped by P0.035.

—

020 (14h)

Mapping parameter 

content #2

B, DEC

Returns the value of P0.026, which is mapped by P0.036.

—

021 (15h)

Mapping parameter 

content #3

B, DEC

Returns the value of P0.027, which is mapped by P0.037.

—

022 (16h)

Mapping parameter 

content #4

B, DEC

Returns the value of P0.028, which is mapped by P0.038.

—

023 (17h)

Mapping monitoring 

variable #1

B, DEC

Returns the value of P0.009, which is mapped by P0.017.

—

024 (18h)

Mapping monitoring 

variable #2

B, DEC

Returns the value of P0.020, which is mapped by P0.018.

—

025 (19h)

Mapping monitoring 

variable #3

B, DEC

Returns the value of P0.011, which is mapped by P0.019.

—

026 (1Ah)

Mapping monitoring 

variable #4

B, DEC

Returns the value of P0.012, which is mapped by P0.020.

—

027 (1Bh)

Z phase offset (PUU 

Unit)

B, DEC

Offset value between motor position and Z phase (Panel only)

PUU

028 (1Ch)

Alarm code

B, DEC

The Error Code (Reserved for future release).

—

029 (1Dh)

Auxiliary encoder 

feedback 

DEC

Position feedback from the auxiliary encoder.

PUU

030 (1Eh)

Position deviation 

(PUU)

DEC

Position deviation between the position command and the feedback position of the auxiliary 

encoder.

PUU

031 (1Fh)

Main / auxiliary 

encoder position 

deviation (PUU)

DEC

Feedback position deviation between the main encoder and auxiliary encoder. 

PUU

035 (23h)

Indexing coordinate 

command

DEC

Current command for the indexing coordinates.

PUU

037 (25h)

Compare data of 

COMPARE

DEC

The actual Compare data is the Compare data plus a specified value: CMP_DATA = DATA_ARRAY[*] 

+ P1.023 + P1.024.

PUU

039 (27h)

DI status (integrated) DEC

Integrated DI status of the drive. Each bit corresponds to one DI channel. Source includes Hardware 

channel / ID281 (P4.007), which is determined by ID268 (P3.006).

—

040 (28h)

DO status (hardware) DEC

Actual status from the DO hardware. Each bit corresponds to one DO channel.

—

041 (29h)

Status of the drive

DEC

Returns ID280 (P4.006) Refer to the description of this parameter.

—

043 (2Bh)

Latest capture data

DEC

The latest data captured by CAP hardware. CAP can continuously capture multiple points.

PUU

048 (30h)

Auxiliary encoder 

CNT

DEC

Pulse counts from the auxiliary encoder.

count

049 (31h)

Pulse command CNT

DEC

Pulse counts from the pulse command (Terminal block input)..

count

050 (32h)

Speed command 

(integrated)

DEC

Integrated Speed command. Source includes analog, register, or position loop.

 0.1 rpm

051 (33h)

Speed feedback 

(immediate)

DEC

Current actual motor speed. 

 0.1 rpm

053 (35h)

Torque command 

(integrated)

DEC

Integrated Torque command. Source includes analog, register, or speed loop.

 0.1%

054 (36h)

Torque feedback

DEC

Current actual motor torque.

0.1%

055 (37h)

Current feedback

DEC

Current actual motor current.

0.01 A (ampere)

056 (38h)

DC Bus voltage

DEC

Rectified capacitor voltage.

0.1 Volt

Table 128 - System Variables Code (Continued)

Code

Variable name

Property

Description

User Unit

(1)

Summary of Contents for Kinetix 5100 2198-E1004-ERS





















































































































































































































































































































































































































































































































Reviews:

No comments