manualshive.com logo in svg

AGFA CR 10-X, Service Manual, Page: 39 / 288

Share
Download
AGFA CR 10-X Service Manual Download Page 39

 
 
DD+DIS155.11E 

Controls, Connections, and Setup Procedures

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 4  CR 10-X / CR Reader / CR 12-X / CR Advanced Reader 

Chapter 1 / Page 3 of 47 

03-2013 

Type 5151 / 100 / 110 / 200 / 210 

Agfa Company Confidential

 

LIST OF CONTENTS 

 

1

 

INTRODUCTION ......................................................................................................................4

 

2

 

INSTALLATION PREPARATION .............................................................................................4

 

2.1

 

Checking Installation Site Prerequisites ...................................................................................5

 

2.2

 

Unpacking the Digitizer .............................................................................................................5

 

2.3

 

Unpacking the NX Workstation and Monitor.............................................................................6

 

2.4

 

Checking the Shipment Completeness.....................................................................................6

 

3

 

PERFORMING THE INSTALLATION STEPS AS DESCRIBED IN THE QUICK 
INSTALLATION GUIDE............................................................................................................7

 

4

 

FINALIZING THE INSTALLATION .........................................................................................10

 

4.1

 

Adding Windows and NX Users..............................................................................................11

 

4.2

 

If required: Configuring Digitizer and NX for the local Network ..............................................15

 

4.3

 

Setup of Connectivity to additional System Components.......................................................17

 

4.4

 

Customizing System Components according to Customer Preferences................................17

 

4.5

 

Finalizing the Workstation Installation ....................................................................................17

 

4.6

 

Checking Software Version.....................................................................................................18

 

4.7

 

Performing further Activities depending on local Regulations ................................................18

 

4.8

 

Customer Training ..................................................................................................................18

 

4.8.1

 

Training for Operating the Digitizer.........................................................................................19

 

4.8.2

 

Training for Usage of Plates and Cassettes ...........................................................................20

 

5

 

APPENDIX: INSTALLATION OF THE DIGITIZER WITHOUT USING THE  CR 10-X / CR 12-
X CONFIGURATION WIZARD ...............................................................................................21

 

5.1

 

Installation Preparation ...........................................................................................................22

 

5.2

 

Connecting the Cables............................................................................................................22

 

5.3

 

Performing Setup of the NX Workstation................................................................................23

 

5.4

 

Verifying the Installation..........................................................................................................43

 

5.5

 

Performing the Installation Wizard of the Digitizer..................................................................45

 

5.6

 

Performing a Backup ..............................................................................................................46

 

5.7

 

Finalizing the Installation.........................................................................................................46

 

6

 

INSTALLATION CHECKLIST .................................................................................................47

 

Summary of Contents for CR 10-X

































































































































































































































































































Reviews:

No comments