manualshive.com logo in svg

AGFA CR 10-X, Service Manual, Page: 166 / 288

Share
Download
AGFA CR 10-X Service Manual Download Page 166

 
DD+DIS155.11E 

Repair and Service

Troubleshooting

 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 2 

CR 10-X / CR Reader / CR 12-X / CR Advanced Reader 

Chapter 3.3 / 18 of 46 

03-2013 

Type 5151 / 100 / 110 / 200 / 210 

Agfa Company Confidential

 

 

 

CODE 

Message 

ARC1200 

IP-transport error. 
 
Meaning: Movement of the Handling has not finished successfully. 
 
The control reached an unexpected situation. 
 
Check the description of the Error Code for more specific information. 
 
Reason 1: Error during operation. 
 
Cure 1: Restart digitizer to perform the startup selftest procedure.  
Watch out for messages, e.g. if an IP has to be removed. 
 
Reason 2: Software problem. 
 
Cure 2: Load new Software. 
 
Reason 3: 'Power Board' defective. 
 
Cure 3: Check 'Power Board' and replace if defective. 

ARC1201 

No IP present at IP Sensor at the end of the tray. 
 
Meaning: Transport of the IP to the 'IP Detection Light Sensor' not successful.  
 
At the IP Detection Light Sensor no IP is detected after the scan movement. 
 
Reason 1: Transport of the IP not successful.  
 
Cure 1: Restart Digitizer. 
 
Reason 2: IP has jammed.  
 
Cure 2: Open Digitizer and remove jammed IP.  

ARC1202 

Unexpected IP found at the beginning of a new cycle.  
 
IP present at IP Detection Light Sensor. 
 
Meaning: At the last cycle the expected transport of the IP into the Cassette 
was not successful.  
 
At the 'IP Detection Light Sensor' an IP is detected at the start movement of the 
new cycle. 
 
Reason 1: Handling of the IP not successful. 
 
Cure 1: Restart Digitizer. 
 
Reason 2: IP has jammed.  
 
Cure 2: Open Digitizer and remove jammed IP.  

Summary of Contents for CR 10-X

































































































































































































































































































Reviews:

No comments