manualshive.com logo in svg

AGFA CR 10-X, Service Manual, Page: 222 / 288

Share
Download
AGFA CR 10-X Service Manual Download Page 222

 
 
DD+DIS155.11E 

Repair and Service

Software Releases and Patches

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 3 

CR 10-X / CR Reader / CR 12-X / CR Advanced ReaderChapter 3.8 / Page 8 of 13 

04-2013 

Type 5151 / 100 / 110 / 200 / 210 

Agfa Company Confidential

 

4 

Software Release ARC_1302 

 

Release Date 

09/2012 

Digitizer SNs 

Software ARC_1302 is installed in digitizers with  
SN 

≥

 1517 and additionally in SN 1381, 1424, 1428, 

1429, 1430, 1433, 1435 

Availability 

  Agfa HealthCare Library* 

  USB flash drive, delivered with the digitizer 

Prerequisites 

The NX workstation connected to the digitizer requires 
software 

≥

 NX 2.0.8700 / 3.0.8700. 

For additional system component compatibility 
information refer to following documents: 

 

Solution Structure Data Document, Document ID* 
30781759 (

Intranet Link

 / 

Extranet Link

) 

 

CR/DR Interoperability Matrix, Document ID* 
31333326 (

Intranet Link

 / 

Extranet Link

) 

Reference Document 

DD+DIS189.12E, Service Bulletin No. 04,  
Software Update ARC_1302 available (

Intranet Link

 / 

Extranet Link

) 

* On the Agfa HealthCare Library only the latest software release can be downloaded.

 

 

4.1 

Solved Software Issues in Software ARC_1302 

 

 

  Solution for Headquarter Complaint HQ_1207130004: 

With ARC_1302 also a new version of the digitizer operating system is installed. This 
solves the issue with some digitizer USB flash drives, being too slow for software 
installation. 

  In software ARC_1201 a workaround was implemented to prevent a software crash in 

case of Photomultiplier flash memory errors. Now the final solution is implemented, to 
prevent read and write errors of the Photomultiplier flash memory.  

  Solved sporadic software issue with error viewer being offline each 15 seconds. The 

issue may appear if digitizer and PC are switched on at the same time. 

  Solved issue with green blinking status LED after scan for several minutes, if an error 

occurred during scan. 

  The feedback messages during service function “endurance run” are now updated with 

each step (feeding IP, scanning, erasing etc.). Before, the feedback messages stopped 
with “feeding IP”, despite endurance run worked fine. 

 

Summary of Contents for CR 10-X

































































































































































































































































































Reviews:

No comments