manualshive.com logo in svg

AGFA CR 10-X, Service Manual, Page: 173 / 288

Share
Download
AGFA CR 10-X Service Manual Download Page 173

 
DD+DIS155.11E 

Repair and Service

Troubleshooting

 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 2 

CR 10-X / CR Reader / CR 12-X / CR Advanced Reader 

Chapter 3.3 / 25 of 46 

03-2013 

Type 5151 / 100 / 110 / 200 / 210 

Agfa Company Confidential

 

CODE 

Message 

ARC2101 

Optic Module operating conditions are not within specification. 
 
Meaning: The 'Optic Module' setting and adjustment are out of specification. 
 
Or the Galvo parameters are not adjustable. 
 
Or the Laser is not working stable.  
 
Or the detection of begin of scan failed. 
 
Or an optical line synchronisation signal is missing during scan. 
 
Reason 1: The 'Optic Module' synchronisation failed because of mechanical 
shock. 
 
Cure 1: Restart Digitizer to get detailed selftest result.  
 
Try to scan an IP again to test the 'Optic Module'.  
 
Reason 2: The software has no current settings for the 'Optic Module'. 
 
Cure 2: Install the newest digitizer software. 
 
Restart Digitizer to get relevant selftest result.  
 
Try to scan an IP again to test the 'Optic Module'. 
 
Reason 3: The cable to 'Optic Module' is defective or disconnected. 
 
Cure 3: Check cable and connectors between 'PMI Board' and 'Optic Module'. 
 
Replace 'Cable PMI Board to Optic Module'. 
 
Reason 4: The 'Optic Module' is defective. 
 
Cure 4: Replace 'Optic Module'.  
 
Reason 5: 'PMI Board' defective. 
 
Cure 5: Replace 'PMI Board'.   

ARC2200 

The shading calibration cannot be performed using the stored calibration file. 
 
Meaning: The stored shading calibration data is not valid any more. Prepare 
image processing failed. 
 
Reason 1: Previous repair with replacement of 'PMT with Light Collector' or 
'Optic Module'. 
 
Cure 1: Perform a shading calibration. 
 
Reason 2: Shading calibration file is corrupt. 
 
Cure 2: Perform a shading calibration. 

Summary of Contents for CR 10-X

































































































































































































































































































Reviews:

No comments