manualshive.com logo in svg

AGFA CR 10-X, Service Manual, Page: 179 / 288

Share
Download
AGFA CR 10-X Service Manual Download Page 179

 
DD+DIS155.11E 

Repair and Service

Troubleshooting

 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 2 

CR 10-X / CR Reader / CR 12-X / CR Advanced Reader 

Chapter 3.3 / 31 of 46 

03-2013 

Type 5151 / 100 / 110 / 200 / 210 

Agfa Company Confidential

 

CODE 

Message 

ARC2504 

Motor error at the Slow Scan Unit. 
 
Meaning: Motor selftest of the 'Slow Scan Motor' detects an error. 
 
Reason 1: The cables are defective or disconnected.  
 
Cure 1: Check cables and connectors between 'Power Board' and 'Slow Scan 
Motor'. 
 
Replace 'Y-Cable Power Board to Motors'. 
 
Reason 2: The 'Slow Scan Motor' is defective.  
 
Cure 2: Replace the 'Slow Scan Motor'. 
 
Reason 3: 'Power Board' defective. 
 
Cure 3: Replace 'Power Board'.  

ARC2600 

Erasure Unit reports supply voltage error. 
 
Meaning: The fuse for supply voltage to the 'Erasure Unit' is defective. 'Power 
Board' defective. 
 
Reason 1: Defective 'Power Board' caused by short circuit at the 'Cable Power 
Board to Erasure Unit'. 
 
Cure 1: Replace 'Power Board' AND 'Cable Power Board to Erasure Unit' 
together! 
 
Reason 2: Defective 'Power Board' caused by short circuit at the 'Erasure Unit'.
 
Cure 2: Replace 'Power Board' AND 'Erasure Unit' together! 

ARC2601 

Erasure Unit reports LED current error. 
 
  
 
Meaning: The Erasure Unit could not be switched on successfully. LED 
currents are not OK. 
 
Reason 1: 'Cable Power Board to Erasure Unit' defective or disconnected. 
 
Cure 1: Check cables and connectors to the 'Erasure Unit'.  
 
Replace 'Cable Power Board to Erasure Unit'. 
 
Reason 2: 'Erasure Unit' current path broken or partly disconnected.  
A LED line is defective. Only one colour 'on' during selftest. 
 
Cure 2: Check the short cable and connector to the overtemperature protection 
at connector P2.  
 
Let the 'Erasure Unit' cool down if hot.  Replace 'Erasure Unit'. 
 
Reason 3: 'Power Board' current path interrupted or electronic driver defect. 
 
Cure 3: Replace 'Power Board'.  

Summary of Contents for CR 10-X

































































































































































































































































































Reviews:

No comments