manualshive.com logo in svg

AGFA CR 10-X, Service Manual, Page: 175 / 288

Share
Download
AGFA CR 10-X Service Manual Download Page 175

 
DD+DIS155.11E 

Repair and Service

Troubleshooting

 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 2 

CR 10-X / CR Reader / CR 12-X / CR Advanced Reader 

Chapter 3.3 / 27 of 46 

03-2013 

Type 5151 / 100 / 110 / 200 / 210 

Agfa Company Confidential

 

CODE 

Message 

ARC2404 

Motor error at the 'IP Drawer Module'. 
 
Meaning: During motor selftest of 'IP Drawer Module' an error occurred. 
 
Reason 1: The cables are defective or disconnected.  
 
Cure 1: Check cables and connectors between 'Power Board' and motor of 'IP 
Drawer Module'.    
 
Replace 'Y-Cable Power Board to Motors'. 
 
Reason 2: The motor of 'IP Drawer Module' is defective.   
 
Cure 2: Replace the 'IP Drawer Module' 
 
Reason 3: 'Power Board' defective. 
 
Cure 3: Replace 'Power Board'.   

ARC2407 

Reference at the 'IP Drawer Module' cannot be detected. 
 
Meaning: The motor drive of the 'IP Drawer Module' does not reach  
 
reference position controlled by 'IP Drawer Light Sensor'. 
 
Reason 1: 'IP Drawer Light Sensor' is out of position. 
 
Cure 1: Bring 'IP Drawer Light Sensor' in correct position. 
 
Reason 2: The cable is defective or disconnected. 
 
Cure 2: Check cables and connectors to 'IP Drawer Light Sensor' of 'IP Drawer 
Module'.  
 
Replace 'Y-Cable Power Board to Drawer/Cass. LS'. 
 
Reason 3: Sensor defective.  
 
Cure 3: Replace 'IP Drawer Light Sensor'. 
 
Reason 4: 'IP Drawer Module' motor drive does not move at all or with difficulty.
 
Cure 4: Check motor drive of 'IP Drawer Module' for proper work and replace if 
damaged.  

Summary of Contents for CR 10-X

































































































































































































































































































Reviews:

No comments