manualshive.com logo in svg

AGFA CR 10-X, Service Manual, Page: 180 / 288

Share
Download
AGFA CR 10-X Service Manual Download Page 180

 
DD+DIS155.11E 

Repair and Service

Troubleshooting

 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 2 

CR 10-X / CR Reader / CR 12-X / CR Advanced Reader 

Chapter 3.3 / 32 of 46 

03-2013 

Type 5151 / 100 / 110 / 200 / 210 

Agfa Company Confidential

 

CODE 

Message 

ARC2602 

Erasure Unit reports LED at standby current error. 
 
Meaning: The 'Erasure Unit' could not be switched off successfully.  
 
LED currents are not OK. The LEDs may still be on! 
 
Reason 1: The 'Power Board' is defective driver or LED sensoric fails. 
 
Cure 1: Replace 'Power Board'.  

ARC2603 

Erase failed. 
 
Meaning: The Erasure procedure failed in active operation. 
 
Reason 1: 'Erasure Unit' or 'Cable Power Board to Erasure Unit' defective. 
 
Cure 1: Restart digitizer to get detailed selftest result.  

ARC2700 

Incorrect Power Board version. 
 
Meaning: Wrong hardware version for 'Power Board' detected during start-up. 
 
This type of digitizer needs a 'Power Board' with increased power output for the 
erasure unit. 
 
Reason 1: 'Power Board' has been mounted, which is incompatible with this 
type of digitizer.  
 
Cure 1: Replace 'Power Board' with compatible version as described in the 
spare parts list.  

ARC2800 

System time error detected. 
 
Meaning: The realtime clock is not usable.  
 
The coin cell battery for the realtime clock at the 'PMI Board' is empty.  
 
The system time is needed to generate unique identifiers as required by 
DICOM.  
 
Reason 1: The battery is disconnected or got loose. 
 
Cure 1: Check proper mounting of the coin cell battery at place B2 on the 'PMI 
Board'. 
 
Check time setting via service tool at item Digitizer-Settings in the webbrowser. 
 
Restart digitizer. 
 
Reason 2: Battery is flat. Battery voltage is too low.  
 
Cure 2: Replace 'PMI Board'.  
 
Check time setting via service tool at item Digitizer-Settings in the webbrowser. 

Summary of Contents for CR 10-X

































































































































































































































































































Reviews:

No comments