manualshive.com logo in svg

AGFA CR 10-X, Service Manual, Page: 40 / 288

Share
Download
AGFA CR 10-X Service Manual Download Page 40

 
 
DD+DIS155.11E 

Controls, Connections, and Setup Procedures

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled. 

 

1 

Introduction 

 

 

IMPORTANT: 

This document describes the installation and configuration of the digitizer including the 
NX workstation with the help of the Quick Installation Guide (part of delivery) and the 
CR 10-X / CR 12-X configuration wizard. 

For installation without using the CR 10-X / CR 12-X configuration wizard refer to the 
appendix, section 5. 

 

 

REQUIRED TOOLS 

The required tools are part of delivery. 

 

 

REQUIRED TIME: 

The complete installation of the digitizer including installation and configuration of the 
workstation takes approximately 1 hour. 

 

 

REQUIRED DOCUMENTS 

Chapter 4 of the corresponding NX Workstation version in the Agfa HealthCare Library: 
Computed Radiography > CR Workstation Software 

 

 

NOTE: 

The 

Installation Checklist

 in section 6 of this chapter gives an overview of all steps  

of the digitizer installation and guides through the complete installation process. 

 

2 

Installation Preparation 

 

 

Preparing the installation is split up into the following steps: 

 

# 

Task  

Section 

1 

Check the installation site prerequisites. 

2.1 

2 Unpack 

the 

digitizer. 

2.2 

3 

Unpack the workstation and monitor. 

2.3 

4 

Check the shipment completeness. 

2.4 

 

 

Edition 1, Revision 4  CR 10-X / CR Reader / CR 12-X / CR Advanced Reader 

Chapter 1 / Page 4 of 47 

03-2013 

Type 5151 / 100 / 110 / 200 / 210 

Agfa Company Confidential

 

Summary of Contents for CR 10-X

































































































































































































































































































Reviews:

No comments