Advanced Instruments 4C3 User Manual Download Page 90

Page: 90 / 139

automatically adjust for voltages between 100VAC and 240VAC but

appropriately rated fuses must be installed. Use 5 x 20mm, 250V,

time delay (Type T) fuses. For 100-130V operation, use 5-Amp

fuses; for 200-240V operation use 2.5-Amp fuses.
Re-install the fuse holder into the back of the instrument and close

the fuse holder door.
If you intend to connect the instrument to a new or different power

outlet, you should first have the outlet ground checked as instructed

in Chapter 1 before re-connecting the instrument power cord.
Re-connect the power cord and switch the power switch to the on

(

) position. The instrument should follow the power-up sequence

described in Chapter 1.

3. Sample Probe Checks

Glass-tipped probes are very sensitive and quick to respond but are

somewhat susceptible to pushing, pulling and bumping damage.

Such damage often causes varying electrical leakage to ground

through the sample and may usually be detected via close visual

inspection or disconnecting the connector and checking the probe

resistance. This can be done in place without disturbing the physical

adjustment of the probe.
The following procedure is recommended for testing and/or replac-

ing the sample probe (please refer to figure 8 for the locations of the

parts named in this procedure):

a. Turn the 4C3 power off and disconnect it from the power

source.

b. Remove 8 screws from the periphery of the back cover of the

instrument and lift it off of the instrument. As you lift off the

back cover, unplug the fan connector.

c. Locate and unplug the sample probe connector (see figure 8).

The probe leads are electrically accessible through the side slots

in the connector. Use care not to touch or bend the connector

pins. Soil or salt from your fingers can increase the electrical

The Advanced

Model 4C3 User’s Guide

Summary of Contents for 4C3












































































































































Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands

Advanced Instruments 4C3, User Manual

Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands