manualshive.com logo in svg

Advanced Instruments 4C3, User Manual

Share
Download
Advanced Instruments 4C3 User Manual Download Page 64

H. Recall

The RECALL button provides access (via the printer and/or serial 

port, not the display), at 

“Cryoscope Ready”

, to the test results 

and messages stored in the instrument memory. This feature is par-

ticularly useful when the printer tape of the required information is 

not available for any reason. 

The information is stored in serial groups called runs, a 

“

run

”

 being 

all of the results and messages stored from the point when a cassette 

is inserted and the START button is pressed, to the point when no 

more cassettes or STAT samples are inserted and the instrument 

reverts to the standby mode and displays 

“Cryoscope Ready”

.

When the recall button is pressed at 

“Cryoscope Ready”,

 

“Recall 1 Run”

 is displayed. Only the results from the last run are 

available if barcoding has been selected, but if barcoding was not 

selected, the operator may either recall the last run accomplished or 

may select up to 9 runs by means of the numeric keypad or the 

<

 or 

>

 button. When more than one run is selected, the output runs will 

be sequential, ending with the last run accomplished. 

NOTE 

If the tests to be recalled were run with either batch num-

bering or barcode scanning enabled, the same mode must be 

enabled during RECALL for the recalled results to be valid.

42

The Advanced

®

 Model 4C3 User’s Guide

Summary of Contents for 4C3












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands