Advanced Instruments 4C3 User Manual Download Page 13

Page: 13 / 139

xiii

Safe Use

• Do not install or use this product in any area subject to extreme

short-term temperature variations, or locations that exceed the speci-

fied operating environment temperatures.

• Never use this product in a wet area.
• To avoid injury or fire hazard, do not operate this product in an

explosive atmosphere.

• Do not install or use the product on an unstable, non-level work sur-

face.

• Do not operate this product with the covers removed or unsecured.

FCC requirements

•

WARNING

: Changes or modifications to this unit not expressly

approved by Advanced Instruments could void the user’s authority to

operate the equipment.

•

NOTE:

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable pro-

tection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interfer-

ence to radio communications. Operation of this equipment in a res-

idential area is likely to cause harmful interference, in which case the

user will be required to correct the interference at his own expense.

Canadian ICES requirements

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil

numérique

de la classe A est conforme à la norme NMB-003 du

Canada.

Summary of Contents for 4C3












































































































































Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands

Advanced Instruments 4C3, User Manual

Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands