Advanced Instruments 4C3 User Manual Download Page 45

Page: 45 / 139

“Select Batch”

, press START to display

“ [ON]< Batch *

[OFF] ”

. The current setting is indicated by the symbol,

“*”

“ [ON]< Batch * [OFF] ”

, press

to toggle the batch

identification option on or off.
Press ENTER to store the new setting (or STOP to restore the orig-

inal setting).

4. Select Barcode

This menu item enables a means of entering an identification num-

ber of up to 16 characters for each test by means of an optional

reading device connected to the barcode port in the back of the

instrument (see figure 7 and section J).

“Select Barcode”

, press START to display

“ [ON]<

Barcode * [OFF] ”

. The current setting is indicated by the sym-

bol,

“*”

“ [ON]< Barcode * [OFF] ”

, press

to toggle the

Barcode option on or off.

Press ENTER to store the new setting (or STOP to restore the orig-

inal setting).

NOTE

Barcode selection automatically includes batch

numbering.

5. Set Stir Amplitude

This menu item displays the current sample stir amplitude setting

and allows the setting to be changed.

At “

Set Stir Amplitude

”, press START to display “

Amplitude =

”.

Installation & Setup

Summary of Contents for 4C3












































































































































Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands

Advanced Instruments 4C3, User Manual

Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands