manualshive.com logo in svg

Advanced Instruments 4C3, User Manual

Share
Download
Advanced Instruments 4C3 User Manual Download Page 57

standards or reference solutions, it is usually best to average 

the readings from three to five aliquots of each sample to avoid 

error. 

 

If you are running the instrument for the first time, it is recom-

mended that you follow the Lactrol

®

 530 reference solution sam-

ples with bracketing calibration standards to check the instru-

ment accuracy and linearity over the range of interest. 

6.   Using the same techniques, unknown samples may be loaded 

into any remaining cassette positions if desired.

7.   Place the first cassette in the left (input) deck, with the labels 

facing you.

8.   Press START. The 4C3 will position the cassette, wipe the 

probe and stir wire between the probe wipers, pick up the first 

sample tube, place it in the sample freezing chamber, and per-

form the freezing point test.

 

The sample temperature will be displayed as soon as it falls 

below 0°C. The 4C3 will freeze the sample at a fixed crystal-

lization point, follow the plateau development, determine the 

freezing point as defined by the plateau mode selected (see 

Chapter 1, Section K), and display and record the results. After 

completing the test, the 4C3 will return the first sample tube to 

the cassette, wipe the probe and return to the cassette for the 

second tube. Figure 9 shows the operating head either loading or 

unloading the third sample tube from a cassette.

 

The 4C3 will automatically index and test each of the remaining 

samples in the cassette in turn, then it will position and test any 

other cassettes in the batch which are placed in the input deck. 

NOTE 

If the STOP button is pressed while testing is in progress, 

the current test will be discontinued and the 4C3 will dis-

play 

“Press Start to Continue, Stop to Quit”

.

 

If 

STOP is pressed the second time, testing will be terminated 

and 

“Cryoscope Ready”

 will be displayed.

 

If testing is stopped during a barcoded test batch, either inten-

tionally or through some mechanical fault, any untested samples 

must be re-scanned.

35

Instrument Operation

Summary of Contents for 4C3












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands