manualshive.com logo in svg

Advanced Instruments 4C3, User Manual

Share
Download
Advanced Instruments 4C3 User Manual Download Page 109

87

Troubleshooting Table

“Result = 0, 

Calibration 

Okay?”

“Standards 

Reversed?”

“Test Time-out 

Error”

“Recalibration 

Needed”

Check the calibration 

(unless running a 0 mOsm 

sample).

Recalibrate unless running 

a 0 mOsm sample.

Calibrate the instrument.

If the error message repeats 

after successful re-calibra-

tion, see Chapter 5, Section 

C for further assistance.

Recalibrate with the correct 

calibration standards.

Did you introduce the 

right calibration standards 

in the right order?

1.  Was the sample OK?
2.  Is the block probe bin 

# correct?

3.  Check the alignment 

by running the Head 

Up/Down Test (see 

Chapter 5, Section 

G.8).

a.  Prepare another sample 

and repeat the test.

b.  Check/correct the block 

probe bin #.

c.  If the error message 

persists, see Chapter 5, 

Section C for further 

assistance.

“Calibration 

Out of Range”

See Symptom item 

“Results not repeatable...”. 

Recalibrate.

Procedure, technique.

“No Plateau”

a.  Test another aliquot of 

that sample in a clean 

sample tube.

b.  If the error message 

persists, see Chapter 5, 

Section C for further 

assistance.

Symptom

Check

Suggested Action

Summary of Contents for 4C3












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands