Advanced Instruments 4C3 User Manual Download Page 75

Page: 75 / 139

• The product is equipped with operator accessible fuses. If a fuse

blows, it may be due to a power surge or failure of a compo-

nent. Replace the fuse only once. If the fuse blows a second

time, it is probably caused by failure of a component part. If this

occurs, refer service to qualified service personnel. Always

replace the fuse with one of the same rating, voltage, and type.

Never replace the fuse with one of a higher current rating.

• When servicing the product, use only factory-specified parts.
•

WARNING:

When returning this product for service, or ship-

ping this product to a second location, remove

all hazardous specimens and decontaminate the

product before packaging for shipment. If the

product cannot be decontaminated, consult with

your shipping agent on appropriate packaging

and marking.

C. How to get service

Before contacting Advanced Instruments for Hot-Line

Technical

Service, be sure to read through this user’s guide for instructions

on routine adjustments, instrument care and troubleshooting. If this

information does not solve the problem, call the appropriate number

below.

• 800-225-4034 (toll-free within the USA and Canada; after

normal business hours, dial extension 2191)

• +US 781-320-9000 (elsewhere)

• 781-320-0811 (fax)

When calling Advanced Instruments, have the model and serial

numbers from the label on the back of the instrument, and a descrip-

tion of the problem. Use a telephone as close to the instrument as

possible to facilitate making recommended diagnostic checks.
A service technician may assist in making minor repairs over the

phone, providing you with recommended parts (or part numbers), or

may issue an authorization to ship the instrument for factory repair.

Troubleshooting & Service

Summary of Contents for 4C3












































































































































Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands

Advanced Instruments 4C3, User Manual

Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands