manualshive.com logo in svg

Advanced Instruments 4C3, User Manual

Share
Download
Advanced Instruments 4C3 User Manual Download Page 113

91

Troubleshooting Table

“Duplicate 

Cassette #”

“Truncated 

Barcode”

Results not 

repeatable    

(too scattered).

“No Barcodes 

for This 

Cassette”

Cassette. Cassettes cannot 

be re-introduced during 

Batch or Barcode runs.

Use a cassette not previ-

ously used in this run or 

start another batch.

Cassette. If an un-scanned 

cassette is introduced 

during a scanned batch 

run, the cassette will be 

tested and the results 

recorded without batch 

identification.

Try to avoid introduc-

ing unscanned cassettes     

during batch test runs.

Try to avoid the use of 

barcodes longer than 

16 characters.

Truncated barcodes lon-

ger than 16 characters 

may appear as duplicate 

entries.

1.  Operator procedures 

and technique.

2.  Check the sample 

probe by running the 

A/D test (see Chapter 

5, Section G).

“Fluid Level = 

Error”

A wiring or circuit board 

error is indicated. If the 

error message persists, see 

Chapter 5, Section C for 

for further assistance.

Symptom

Check

Suggested Action

See Chapter 2,       

Sections D and G.
Replace the sample 

probe (see Chapter 4, 

Section G).
If the error message 

persists, see Chapter 5, 

Section C for further 

assistance.

Summary of Contents for 4C3












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands