Advanced Instruments 4C3 User Manual Download Page 48

Page: 48 / 139

“ [ON]< Capture *[OFF] ”

, press

to enable or disable

communication-port data capture.

Press ENTER to store the new setting (or STOP to restore the orig-

inal setting).

10. Select Xon/Xoff

This menu item enables or disables the Xon/Xoff handshaking pro-

tocol for EIA-232/V.24 communication.

At “

Select Xon/Xoff

”, press START to display “

[ON]< Xon/Xoff

*[OFF]

”. The current setting is indicated by the symbol,

“*”

At “

[ON]< Xon/Xoff *[OFF]

”, press

to enable or disable

serial-port Xon/Xoff handshaking.

Press ENTER to store the new setting (or STOP to restore the orig-

inal setting).

11. Select Plateau Mode

This menu item enables changing the way the 4C3 evaluates the

plateau. The rationale for each evaluation mode is outlined in the

Foreword.

This instrument is equipped to use several methods of plateau

determination. These are grouped into two types,

TIMED

and

SEEKING

. Setup menu item #10, “

Select Plateau Mode

” is

used along with the “<” or “>” keys to cycle through the choice of

30-second timed plateau, and IDF 108B or ISO 5764 plateau seek-

ing methods. The proper selection will depend on your laboratory

practices and national requirements. Once selected, your instrument

will base its final result on the required timing and limits imposed

by each standard.

The Advanced

Model 4C3 User’s Guide

Summary of Contents for 4C3












































































































































Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands

Advanced Instruments 4C3, User Manual

Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands