manualshive.com logo in svg

Advanced Instruments 4C3, User Manual

Share
Download
Advanced Instruments 4C3 User Manual Download Page 85

Press STOP to exit to the test menu. Then remove the temporary 

loop-back connector. 

CAUTION 

If the loop-back connector is not removed after this 

test, the instrument will not function.

5. Display/Print Test

This test is a simple check of the display and printer. 

On entry, a series of characters should scroll across the display (and 

a single line of the same characters should print out on the printer). 

The characters displayed have been chosen to illuminate every dot 

in the character matrix. This makes it possible to distinguish any 

dots that no longer work, on the printer as well as the display.

Press STOP to exit to the test menu.

6.  Beeper Test

This test exercises the beeper.

On entry, 

“[on] beeper [off]” 

is displayed. Press the 

<

 button to 

cause the beeper to beep repeatedly; press the 

>

 button to stop the 

beeper. 

Press STOP to exit to the test menu.

7.  Keypad Test

This test enables checking each button on the keypad, as well as 

the lamps of each illuminated button. As each button is pressed, its 

name should be displayed and the lamp of each illuminated button 

should light. 

Press the STOP button to exit to the test menu after a momentary 

pause.

63

Troubleshooting & Service

Summary of Contents for 4C3












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands