manualshive.com logo in svg

Advanced Instruments 4C3, User Manual

Share
Download
Advanced Instruments 4C3 User Manual Download Page 110

88

The Advanced

®

 Model 4C3 User’s Guide

“Sample Did 

Not Freeze”; 

“Sample 

Freeze Error”

Freeze “buzz” occurred

1.  Was the sample tube 

left empty?

2.  Is the freezing point 

of the sample beyond 

the range of the instru-

ment (see Appendix 

B)?

3.  Does the sample con-

tain many small bub-

bles or froth?

4.  Is the sample very vis-

cous?

5.  Is the probe configura-

tion correct?

a.  Test another aliquot of 

that sample in a clean 

sample tube.

b.  Try testing samples 

known to be within the 

range of the instrument.

c.  Make sure samples 

contain no bubbles or 

froth before testing.

  Decrease the sample 

stir amplitude, if neces-

sary, to avoid generat-

ing bubbles before the 

freeze buzz occurs.

d.  The 4C3 is not 

designed to test thick or 

very viscous samples.

e.  Check/correct the probe 

bin numbers.

f.  Test another aliquot 

of that sample in a 

clean sample tube (see 

Chapter 2, Sections D 

and G).

Symptom

Check

Suggested Action

Summary of Contents for 4C3












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands