manualshive.com logo in svg

Advanced Instruments 4C3, User Manual

Share
Download
Advanced Instruments 4C3 User Manual Download Page 103

81

Troubleshooting Table

If not followed by “Reset 

Probe Configuration”, see 

Chapter 5, Section C for 

further assistance.
If followed by “Reset 

Probe Configuration”, see 

Symptom item “Reset 

Probe Configuration”...

“Parameter 

RAM Failed” 

or “New 

Software 

Version”

“Reset Probe 

Configuration” 

displayed 

during the 

power-up 

sequence

If not followed by “Select 

Test Item”, see Chapter 

5, Section C for further 

assistance.
If followed by “Select 

Test Item”, see Symptom 

item “Thermoelectrics 

Driver Failure”

“Reset Probe 

Configuration” 

displayed 

during the 

power-up 

sequence, 

followed by 

“Select Test 

Item”

(If not followed by 

“Select Test Item”, see 

Chapter 5, Section C for 

further assistance.

a.  Press > to advance 

to “Set Block Probe 

Bin #” in the SETUP 

menu and reset the 

block probe bin # (see 

Chapter 1, Section 

K.1).

Switch the instrument 

off, then on.

If the error message 

persists, see Chapter 5, 

Section C for further 

assistance.

Symptom

Check

Suggested Action

Summary of Contents for 4C3












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands