Advanced Instruments 4C3 User Manual Download Page 9

Page: 9 / 139

Calibrators & Standards

DESCRIPTION

-422 m°H Calibration Standard (-408 m°C)
-621 m°H Calibration Standard (-600 m°C)
-530 m°H Lactrol

530 Reference Solution (-512 m°C)

PART NO.

3LA023
3LA033
3LA030

To order calibrators and standards, contact the Advanced

Instruments Customer Service Department by using one of the fol-

lowing numbers.

•

800-225-4034 (toll-free within the USA and Canada)

•

+US 781-320-9000 (elsewhere)

•

781-320-3669 (fax)

NOTE

Advanced Instruments cannot guarantee the stated

instrument performance specifications and accuracy of

test results unless Advanced Instruments brand consum-

ables are used with the instrument. Use of consumables

from manufacturers other than Advanced Instruments

is not recommended and may adversely affect system

calibration, performance, operation, and accuracy of test

results. For information on obtaining these standards

and controls, contact Advanced Instruments or an autho-

rized representative.

Summary of Contents for 4C3












































































































































Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands

Advanced Instruments 4C3, User Manual

Search results

Summary of Contents for 4C3

Reviews:

Brands by name

Popular brands