manualshive.com logo in svg

3Com 8800 SERIES, Configuration Manual

The 3Com 8800 SERIES is a versatile networking solution that offers seamless connectivity. For a hassle-free installation, users can download the comprehensive Installation Manual for free from our website. This manual provides step-by-step instructions to ensure a smooth setup process, allowing you to make the most of this exceptional product.

Share
Download
background image

3Com Switch 8800 Configuration Guide 

Chapter 7  Link Aggregation Configuration

 

7-1 

Chapter 7  Link Aggregation Configuration 

7.1  Overview 

7.1.1  Introduction to Link Aggregation 

Link aggregation means aggregating several ports together to implement the 

outgoing/incoming payload balance among the member ports and enhance the 

connection reliability. Link aggregation may be manual aggregation, dynamic LACP 

aggregation or static LACP aggregation. For the member ports in an aggregation group, 

their basic configurations must be the same. That is, if one is a trunk port, others must 

also be; when it turns into access port, then others must change to access port. 

Basic configuration includes STP setting, QoS setting, VLAN setting, and port setting. 

The STP setting includes STP enabling/disabling, link attribute (point-to-point or not), 

STP priority, path cost, max transmission speed, loop protection, root protection, edge 

port or not. The QoS setting includes traffic limiting, priority marking, default 802.1p 

priority, bandwidth assurance, congestion avoidance, traffic redirection, traffic statistics. 

The VLAN setting includes permitted VLAN types, default VLAN ID. The port setting 

includes port link type. 

One Switch 8800 can support up to 728 aggregation groups (seven load sharing 

aggregation groups at most), with each group containing a maximum of eight ports. 

 

 

  Note: 

The Switch 8800 also supports trans-board aggregation. The trans-board aggregation 

is the same as the intra-board aggregation. 

 

7.1.2  Introduction to LACP  

Link aggregation control protocol (LACP) based on the IEEE802.3ad standard can be 

used in dynamic link aggregation. An LACP-enabled port sends link aggregation 

control protocol data units (LACPDUs) to tell the peer about its system priority, system 

MAC address, port priority, port number and operation key. After receiving the 

information from the sender, the receiver compares it with the locally saved information 

about other ports, chooses member ports for the aggregation group and reaches 

agreement about if a port can join or leave a dynamic aggregation group. 

During port aggregation, LACP generates a configuration mix according to the port 

configuration (rate, duplex, basic configuration, management key), which is called an 

Summary of Contents for 8800 SERIES






































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8800 SERIES

Makita RF1101 Parts Breakdown preview
RF1101
Brand: Makita Pages: 2
MA lighting grandMA2 Series Quick Manual preview
grandMA2 Series
Brand: MA lighting Pages: 36
Tripp Lite N125-010-GY Specification Sheet preview
N125-010-GY
Brand: Tripp Lite Pages: 2
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Brand: Texas Instruments Pages: 179
FOR-A USF-105AS Operation Manual preview
USF-105AS
Brand: FOR-A Pages: 39
Justec JDR454WV4 User Manual preview
JDR454WV4
Brand: Justec Pages: 61
Tbus NV-ER1816i Installation Manual preview
NV-ER1816i
Brand: Tbus Pages: 25
Faderfox 4midiloop User Manual preview
4midiloop
Brand: Faderfox Pages: 10
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
Netis DL4305D Quick Installation Manual preview
DL4305D
Brand: Netis Pages: 16
IBM System Storage DS3200 Overview preview
System Storage DS3200
Brand: IBM Pages: 2
Idis DR-1500 Series Quick Manual preview
DR-1500 Series
Brand: Idis Pages: 17
Planet IGS-5225-20T4C2X Quick Installation Manual preview
IGS-5225-20T4C2X
Brand: Planet Pages: 16
Matrix Switch Corporation MSC-1HD1608L Product Manual preview
MSC-1HD1608L
Brand: Matrix Switch Corporation Pages: 60
Buffalo BS-GS2008P Quick Setup Manual preview
BS-GS2008P
Brand: Buffalo Pages: 2
Abocom 802.11a/b/g SDIO WiFi Module SDM3100 User Manual preview
802.11a/b/g SDIO WiFi Module SDM3100
Brand: Abocom Pages: 14
Linksys WRK54G User Manual preview
WRK54G
Brand: Linksys Pages: 80
MiLAN MIL-SME801GLX User Manual preview
MIL-SME801GLX
Brand: MiLAN Pages: 155

Brands by name

Popular brands

Load more brands