Whirlpool M-17 Скачать руководство пользователя

Страница: 31 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

2-11

Troubleshooting Guide (Continued)

CUSTOMER DESCRIPTION

POTENTIAL CAUSES

CHECK

RELATED

ERROR

CODES

Won't start and Start/Resume

LED flashes 3 times when

Start/Resume key is pressed

Control looking for door to open

between cycles:

˗ Customer has not opened door since

last cycle

˗ Door switch contacts stuck closed

Refer to “

Service Error Codes

” table.

F5E2

Won't accept key presses and

Control Lock LED on

Control lockout feature accidentally

enabled by customer.

Instruct customer. Refer to

Owner's

Manual

. Press and hold Control Lock key

for 5 seconds to disable lockout feature.

One or more keys won't

respond or unusual key/LED/

display behavior

Stuck key or short circuits in keypad or

in user interface's input lines that read

the keys.

Refer to “

Service Error Codes

” table.

F2E1

Capacitive touch keypad adhesive

coming loose from console.

1. Unplug dishwasher or disconnect

power.

2. Inspect keypad board for separation

from console. Replace keypad/console

if separation is seen.

Loose connections between keypad and

control and/or bent connector pins.

1. Unplug dishwasher or disconnect

power.

2. Inspect connections in user interface

circuits. Reconnect loose connections.

Replace parts if pins are damaged or

contaminated.

F6E1

Excessive condensation on user interface

parts due to vent and/or fan problem.

Check fault code history for vent and/or

fan faults. Refer to “

Service Error Codes

”

table. Verify that vent closes and fan turns

on. Refer to "Leaks or drips on cabinet or

floor."

F10E2 (FAE2)

F10E3 (FAE3)

User interface failure.

1. Unplug dishwasher or disconnect

power.

2. Replace user interface.

Dishwasher beeps constantly

User opened door during cycle and

closed door without pressing

Start/Resume key to resume cycle.

Instruct customer. Control is designed to

beep if dishwasher is in "cycle interrupt"

mode with door latched. Control will stop

beeping when door is open and/or when

Start/Resume key is pressed to resume

cycle.

Normal beeper operation is excessive to

customer.

Instruct customer how to turn beeper off

and on. Refer to

Owner's Manual

Control is programmed to stop cycle and

alert customer when certain fault codes

have been detected.

Press Cancel key once to silence alarm

during fault mode. Read error code from

the dishwasher and refer to “

Service Error

Codes

” table. Use service diagnostics

mode to get fault history from appliance.

F1E1

F7E1

F7E2

F8E1

F8E4

F8E5

F9E1

F10E5 (FAE5)

LEDs or displays run for a

short time without loads

running or wash motor runs

without attempt to fill or fan

is the only load that runs

Unit is in sales demo mode

Check operation of Cancel key. If pressing

cancel multiple times does not activate

Cancel/Drain sequence, unit is likely in

sales demo mode. To clear demo mode,

cycle power for at least 1 minute or run

service diagnostics cycle.

Open fuse on control removed power

from loads

Refer to “Fuse Service and Resistance

Check” in section 3.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды