Whirlpool M-17 Скачать руководство пользователя страница 29

Страница: 29 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

2-9

Service Error Codes (Continued)

FUNCTION CODE ERROR CODE

CAUSES

WHAT TO CHECK

9 - Draining

4 - Light in the

tub

Loose connection or open in tub light

circuit

1. Unplug dishwasher or disconnect power.

2. Check resistances of tub lights and all connections

in tub light circuit. Fix/replace open connection/

part.

10 (A) - Other

1 - Dispenser

electrical

problem

Loose connection in dispenser circuit

and/or open dispenser solenoid

1. Unplug dishwasher or disconnect power.

2. Check resistances of dispenser solenoid and all

connections in the dispenser circuit. Fix/replace

open connection/part.

Open fuse on control to dispenser

Refer to “Fuse Service and Resistance Check” in

section 3.

Dispenser drive circuit on control

1. Unplug dishwasher or disconnect power.

2. Check resistances of dispenser solenoid and

all connections in the dispenser circuit. If all

connections and solenoid measure good, replace

control.

2 - Vent

electrical

problem

Loose connection in vent circuit

and/or open vent wax motor.

1. Unplug dishwasher or disconnect power.

2. Check resistances of vent wax motor and all

connections in the vent circuit. Fix/replace open

connection/part.

Open fuse on control to vent.

Refer to “Fuse Service and Resistance Check” in

section 3.

Vent drive circuit on control.

1. Unplug dishwasher or disconnect power.

2. Check resistances of vent wax motor and all

connections in the vent circuit. If all connections

and wax motor measure good, replace control.

3 - Drying

fan electrical

problem

Loose connection in fan circuit and/or

open fan motor winding.

1. Unplug dishwasher or disconnect power.

2. Check resistances of fan motor and all connections

in the fan circuit. Fix/replace open connection/

part.

Fan drive circuit on control.

1. Unplug dishwasher or disconnect power.

2. Check resistances of fan motor and all connections

in the fan circuit. If all connections and fan motor

measure good, replace control.

4 - Diverter can't

find positions

Corroded or loose connection in

diverter sensor or motor circuit. Open/

shorted diverter sensor or motor.

1. Unplug dishwasher and disconnect power.

2. Check connections in diverter sensor and motor

circuit with meter. Fix/replace connections/parts.

Inspect diverter for evidence of water or

contaminants; if yes, replace.

5 - Diverter leak

Corroded or loose connection in

diverter sensor circuit.

1. Unplug dishwasher and disconnect power.

2. Check connections in diverter sensor circuit with

meter. Fix/replace connections/parts.

Leak at diverter seal

Inspect diverter for evidence of water or

contaminants; if yes, replace.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды