Whirlpool M-17 Скачать руководство пользователя страница 52

Страница: 52 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

3-14

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Overfill Switch Circuit

Perform the following checks if the dishwasher detects F8E4

when there is no water in the leak pan, or if F8E4 is not detected

when water is present in the leak pan. The following items are

part of the overfill switch circuit:

Harness/Connection

Overfill Switch/Float Assembly

Control Board

Test Procedure

Unplug dishwasher or disconnect power.

Remove toe and outer door panels to access leak pan and

control board.

Check leak pan for water. If no water is present, go to step 5.

If leak pan is full of water, unplug float switch, remove pan

and empty. Replace pan and reconnect float switch.

Reconnect power. If F8E4 fault does not return, find source of

leak and repair.

NOTE:

If root cause of overfill is not corrected, customer will

experience another overfill and service call in the future.

Strip Circuit - Overfill Switch

Inspect float assembly. Verify that connector is fully seated.

Ensure that Styrofoam floater moves freely up and down and

no debris is preventing it from sitting in the down (closed)

position.

If no issue found, go to step 6.

Repair/reconnect if any issues found.

Disconnect connector P11 from control board.

Using an Ohmmeter, measure across P11 pins 6 and 7 with

the float assembly connected and installed in the leak pan.

If 3 ohms or less is measured, go to step 8.

If high resistance is measured, check for loose

connections and repair/replace as needed.

Using an Ohmmeter, measure across P11 pins 6 and 7 with

the Styrofoam floater lifted up (switch should be open).

If reading is infinite, go to step 9.

If reading shows continuity, replace float assembly and

retest.

Set meter to DC and connect leads to P11 pins 6 and 7.

10.

Plug in dishwasher or reconnect power and verify that

13 VDC is present across P11 pins 6 and 7 with P11

disconnected from the board.

If 13 VDC is not present, replace the control and retest.

If 13 VDC is present, proceed to step 10.

11.

Reconnect P11 to control board and run Diagnostics cycle to

confirm operation.

12.

Reassemble all parts and panels. Ensure that float assembly is

connected, seated in leak tray, and tray is reinstalled.

13.

Plug in dishwasher or reconnect power.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Electronic Control

P11-7

Electronic Control

P11-6

Input

13 VDC

Overfill Switch

(In normal position, float

assembly holds switch closed)

N.O.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды