Whirlpool M-17 Скачать руководство пользователя

Страница: 61 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

3-23

Interior LED Lighting (some models)

This test will check the wiring to the LED tube lights and the lights

themselves. The following items are part of the LED Tube Lights

circuit:

Harness/Connection

LED Tube-lights (2)

Control Board

Under normal operation

•

The Interior LED Lighting is not on during the wash cycle.

•

The Interior LED Lighting turns on when the door is opened

and remains on for 10 minutes.

Test Procedure

NOTE:

The two (2) LED Tube-lights are wired in parallel. It is

possible for one light to malfunction and the other to remain

operational.

Strip Circuit -Interior LED Lighting

Open dishwasher door. The Interior LED Lights should

turn on. The following steps assume that this step was

unsuccessful.

Unplug dishwasher or disconnect power.

Remove toe and outer door panels to access control board.

Visually check that the P9 connector on the control is

securely installed.

If visual passes, go to step 5.

If the connector is not inserted properly, reconnect and

retest Interior LED Lighting.

Disconnect P9 from the Control Board.

Measure each LED light individually using the diode check

setting on the multimeter. Meter should display a numeric

reading from anode to cathode and "OL" reading from

cathode to anode (refer to strip circuit below).

If LED check passes, go to step 7.

If any of the LEDs do not pass the check, replace the

defective LED individually and retest Interior LED lighting.

Set voltmeter to DC and connect red lead to P9-3 and

black lead to P9-4 on the control board. Plug in dishwasher or

reconnect power.

Measure for 13 VDC between P9-2 and P9-4 with lights

disconnected and door opened. Light output must be

measured within 10 minutes of opening the door.

If 13 VDC is not present, replace the control and retest.

If 13 VDC is present, proceed to step 9.

Unplug dishwasher and disconnect power.

10.

Reassemble all parts and panels.

11.

Plug in dishwasher or reconnect power.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Electronic Control

P9-4

Electronic Control

P9-3

Ref

13 VDC

Light

Pin 3

Pin 1

Pin 3

Light

Pin 1

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды