Whirlpool M-17 Скачать руководство пользователя страница 55

Страница: 55 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

3-17

Wash Motor RIF

This test will check the wiring to the wash motor and the wash

motor itself. The following items are part of the wash motor

circuit:

Harness/Connection

Wash Motor and Capacitor

Control Board

Wash motor fuse (Some models)

Test Procedure

Check the tube and sump for anything that may be impeding

water flow. Inspect and if necessary clean the coarse-filter

system. Also, inspect spray arm water nozzles and clean if

needed.

Check the wash motor and electrical connections by

performing the Service Diagnostics Cycle. The following steps

assume that this step was unsuccessful.

Unplug dishwasher or disconnect power.

Remove toe and outer door panels to access control board.

Unplug connector P5 from control board.

Check the wash motor using an ohmmeter, measure the

resistance between P5-1 and P5-2.

If the resistance is between 10-15 ohms, the wash motor

and harness are good. Go to step 7.

If outside the range, replace the wash motor.

If an open circuit is detected, check connections and

harness continuity between control and wash motor. If

good, replace the wash motor.

Strip Circuit - Wash Motor RIF

Check the motor fuse (Some models). Using an ohmmeter,

measure the resistance between P5-1 and P5-4 on the

control.

If the resistance is less than 3 ohms, fuse is good. Go to

step 8.

If the resistance is greater than 3 ohms, replace the

control.

Reconnect P5 to control board.

Set voltmeter to AC and connect leads to test-pads.

10.

P5-1 and P5-2 on the control board. Plug in dishwasher or

reconnect power.

11.

Start the Diagnostics Cycle and at the proper interval

measure for AC out of the control board between P5-1 and

P5-2 (Refer to Wash Motor Strip Circuit below).

If no AC voltage is measured, replace the control board

and retest.

If 120 VAC is measured and wash motor is running, go to

step 12.

If 120 VAC is measured and wash motor is not running, go

to step 10.

12.

Test the wash motor capacitor.

NOTE

: A faulty capacitor may cause the motor to "hum", not

start, or start slowly.
A. Discharge the capacitor by touching the leads of a

20,000 ohms resistor to the two terminals.

B. Disconnect the wires from the capacitor terminals.
C. With an ohmmeter, measure across the terminals and

note reading.

If a steady increase in resistance is noted, capacitor is

good. Replace wash motor assembly and retest.

If the capacitor is either shorted or open, replace

capacitor and retest.

If the preceding steps did not correct the wash motor

problem, replace the control board.

13.

Unplug dishwasher or disconnect power.

14.

Reassemble all parts and panels.

15.

Plug in dishwasher or reconnect power and run Diagnostics

Cycle to verify repair.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

TURQ

(LBU)

Electronic Control

P5-1

Pin 3

K502

Motor N Relay

(Also see Door

Switch Circuit)

P5-2

P4-4

Sense Resistor

or Jumper

Pin 2 AUX

Winding

10 Ω - 12 Ω

CAP

23.5

Run

Winding

7 Ω - 9 Ω

at 25°C

Motor and Capacitor

(Wash Pump)

120 V

, 60 Hz, 90 W (No load)

TURQ

(LBU)

Electronic Control

N.O.

Fuse

F501

(Some models)

N.O.

K503

Pilot L1 Relay

(Also see Door

Switch Circuit)

P4-1

210 W (Full load)

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды