Whirlpool M-17 Скачать руководство пользователя страница 62

Страница: 62 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

3-24

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

ACU Diagnostic LED

The control is equipped with a single LED which is intended to

help diagnose if the ACU needs to be replaced. The LED has

different display patterns which indicate different states.

LED Slow Blinking:

Normal ACU operation. Unrecoverable ACU

fault has been recorded. Power supply and microcontroller are

functional.

LED Solid ON:

Power is applied to ACU, but no Setting File has

been programmed. Control is not functional in this state. Flash

Setting File (if service tool is available) or replace ACU.

LED Double Blink:

Communication failure between ACU and HMI.

LED Fast Blink:

ACU is performing initialization or ACU setting file

is in progress of being programmed. This should be a temporary

state that occurs briefly at power up.

LED OFF:

An unrecoverable ACU fault has been recorded or no

power is applied to ACU. Check for 120 VAC across P4-1 and P4-4.

See “Service Fault Codes” table above.

LED Triple Blink:

Incompatibility between ACU Setting File and

firmware.

User Interface (UI)

This test will check the wiring to the user interface and the user

interface itself. The following items are part of the user interface

circuit:

Harness/Connection

User Interface (UI)

Status LED (On some models)

Control Board

Test Procedure

Verify that the control lock-out feature has not been turned

on by the customer. If unit will not run or power up, perform

Power Check procedure on page

3-8

. Also, check for excessive

condensation on UI parts due to vent and/or fan problem.

Unplug dishwasher or disconnect power.

Remove toe and outer door panels to access control board.

Disconnect user interface connection from control board.

Verify all other connections to the control are good.

Plug in dishwasher or reconnect power.

Perform DC power supply voltage checks as described above

in “General Theory of Operation” section.

Repair/replace faulty parts.

Unplug dishwasher or disconnect power.

Reassemble all parts and panels.

10.

Plug in dishwasher or reconnect power.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды