Whirlpool M-17 Скачать руководство пользователя страница 56

Страница: 56 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

3-18

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Global Wash Motor SSM

This test will check the wiring to the wash motor and the wash

motor itself. The following items are part of the wash motor

circuit:

Harness/Connection

Wash Motor

Control Board

Wash Motor Fuse (Some Models)

Test Procedure

Check the tube and sump for anything that may be impeding

water flow. Inspect and if necessary clean the coarse-filter

system. Also inspect spray arm and nozzle and clean if

needed.

Check the wash motor and electrical connections by

performing the Service Diagnostics Cycle. The following steps

assume that this step was unsuccessful.

Unplug power or disconnect dishwasher.

Strip Circuit - Single Speed Wash Motor

Remove toe and outer door panels to access control board.

Unplug connector P5 from control board.

Check the wash motor using an ohmmeter, measure the

resistance between P5-1 and P5-2.

If the resistance is between 7-12 ohms, the wash motor

and harness are good. Go to step 7.

If outside the range, replace the wash motor.

If an open circuit is detected, check connections and

harness continuity between control and wash motor. If

good, replace the wash motor.

Check the wash motor fuse (some models). Using an

ohmmeter, measure the resistance between P5-1 and P5-4.

If the resistance is less than 3 ohms, fuse is good. Go to

step 8.

If the resistance is greater than 3 ohms, replace the

control.

Reconnect P5 to control board.

Set voltmeter to AC and connect leads to test-pads

P5- 1 and P5-2 on the control board. Plug in dishwasher or

reconnect power.

10.

Start the Diagnostics Cycle and at the proper interval

measure for AC out of the control board between P5-1 and

P5-2 (Refer to Wash Motor Strip Circuit below).

If no AC voltage is measured, replace the control board

and retest.

If 120 VAC is measured and wash motor is running, go to

step 11.

If 120 VAC is measured and wash motor is not running, go

to step 9.

11.

Unplug dishwasher or disconnect power.

12.

Reassemble all parts and panels.

13.

Plug in dishwasher or reconnect power and run Diagnostics

Cycle to verify repair.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

P4-1

P5-1

TURQ

(LBU)

N.O.

K503

Pilot L1 Relay

(Also see Door

Switch Circuit)

Fuse F501

Electronic Control

Pin 2

Pin 3

(Some Models)

TURQ

(LBU)

1-PH SYNC

WASH

MOTOR

PUMP

120 V / 60 Hz

26 - 36 W

7.5 - 9 Ω at 25°C

K502

Motor N Relay

(Also see Door

Switch Circuit)

P5-2

P4-4

Sense Resistor

or Jumper

Electronic Control

N.O.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды