Whirlpool M-17 Скачать руководство пользователя страница 22

Страница: 22 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

2-2

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Safety

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

Voltage Measurement Safety Information

When performing live voltage measurements, you must do the following:

■

Verify the controls are in the off position so that the appliance does not start when energized.

■

Allow enough space to perform the voltage measurements without obstructions.

■

Keep other people a safe distance away from the appliance to prevent potential injury.

■

Always use the proper testing equipment.

■

After voltage measurements, always disconnect power before servicing.

IMPORTANT

Electrostatic Discharge (ESD) Sensitive Electronics

ESD problems are present everywhere. ESD may damage or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress.

■

Use an antistatic wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the
appliance

-OR-

Touch your finger repeatedly to a green ground connection point or unpainted metal in the appliance.

■

Before removing the part from its package, touch the antistatic bag to a green ground connection point or
unpainted metal in the appliance.

■

Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.

■

When repackaging failed electronic control assembly in antistatic bag, observe above instructions.

IMPORTANT SAFETY NOTICE — “For Technicians only”

This service data sheet is intended for use by persons having electrical, electronic, and

mechanical experience and knowledge at a level generally considered acceptable in the

appliance repair trade. Any attempt to repair a major appliance may result in personal

injury and property damage. The manufacturer or seller cannot be responsible, nor

assume any liability for injury or damage of any kind arising from the use of this data

sheet.

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды