Whirlpool M-17 Скачать руководство пользователя страница 36

Страница: 36 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

2-16

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Troubleshooting Guide (Continued)

CUSTOMER DESCRIPTION

POTENTIAL CAUSES

CHECK

RELATED

ERROR

CODES

Sanitized LED blinks or

incomplete sanitization

message at end of cycle

(Control could not confirm

sanitization achieved)

Loose or intermittent connection in door

switch circuit:

˗ Sloppy door latch assembly (Can

be aggravated by high door closure

force keeping strike plate from fully

seating).

1. Check strike plate and door closure

force. Verify door seal is seated

properly. Check for interference

between dish racks and door. Try

bending strike plate down for better

engagement.

2. Unplug dishwasher or disconnect

power.

3. Check resistances of door switch

contacts and all connections in the door

switch circuit with meter, while opening

and closing the door latch.

˗ If high resistance with door closed,

check/fix loose connections.

Measure resistance of door switch

contacts while checking mechanical

operation of latch assembly. Check for

broken plastic pieces on latch assembly.

Replace latch if faulty.

Line voltage too low to heat fast enough

for sanitization.

Confirm at least 100 VAC at power source.

Air pressure surges due to washing with

high suds causes brief opening of door

switch contacts during final rinse.

Refer to “

Service Error Codes

” table.

F8E3

Melted dishware and/or spray

arm and/or dishwasher always

hot

Customer uses non-dishwasher safe

dishes or loads plastic dishes directly

over heater

Instruct customer.

Temperature sensing problem

Refer to “

Service Error Codes

” table.

F3E1

Heating problem

Refer to “

Service Error Codes

” table.

F4E2

F4E3

Heater displaced from mounting clip

and/or pulled off center

Inspect heater. Adjust back into position if

needed.

Noisy operation

Spray arm stalled or blocked and

spraying on door

˗ Instruct customer if blocked

˗ Check spray arm rotation and check

for plugged nozzles. If plugged, clean

nozzles and inspect filters.

Diverter problem

Refer to “

Service Error Codes

” table.

F10E4 (FAE4)

No or low water

Refer to “

Service Error Codes

” table.

F8E1

F8E2

F8E3

Drain periods are too long

Control is programmed to run drain until

complete. Long or partially obstructed

drain hose may cause long drain periods.

Run Service cycle and verify that drain is

completed in approximately 1 minute.

If drain is long, inspect drain path from

dishwasher to customer's plumbing for

issues.

Loose connection in vent circuit and/or

open vent wax motor

Unplug dishwasher or disconnect power

and check resistances of vent wax motor

and all connections in vent circuit. Fix/

replace open connections/part.

F10E2 (FAE2)

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды