Whirlpool M-17 Скачать руководство пользователя

Страница: 50 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

3-12

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Water Heating/Heat Dry

This test will check the wiring to the heater element, hi-limit

thermostat and the heating circuit itself. The following items are

part of the heater circuit:

Harness/Connection

Heater Coil

Hi Limit Thermostat

Control Board

Test Procedure

Control is programmed to disable the heater if it detects a

problem with the heating system. This check is performed at the

start of a heating period in each cycle. If heating problem is not

corrected, the control will disable the heater again.

Unplug dishwasher or disconnect power.

Remove toe and access panels to outer door control board.

Disconnect P4 from the control board.

Strip Circuit - Heater Circuit

Using an ohmmeter, measure resistance between P4,

pins 2 and 3.

If the resistance is between 10-40 ohms, go to step 6.

If an open circuit is detected, go to step 5.

Visually check the wire connections between the control

board, the heater element and the hi-limit thermostat. If the

connections look good, check for continuity across the heater

element and the hi-limit.

Replace heater element or hi-limit thermostat if it is

electrically open.

Repair or replace wire harness if test fails continuity.

Reconnect P4 to control board.

Set voltmeter to AC and connect leads to test-pads P4-2 and

P4-3 on the control board. Plug in dishwasher or reconnect

power.

Start the Diagnostics Cycle and at the proper interval

measure for AC out of the control board between P4-2 and

P4-3 using a voltmeter set to AC.

If 120 VAC is measured and heater element is on, go to

step 9.

If no AC voltage is measured, replace control board.

Perform Diagnostics Cycle to verify repair.

If heater related error still exists, perform Water Sensing

test procedure on following page.

10.

Unplug dishwasher or disconnect power.

11.

Reassemble all parts and panels.

12.

Plug in dishwasher or reconnect power.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Electronic Control

N.O.

K505

Heater L1 Relay

(Also see Door

Switch Circuit)

Hi-Limit

Thermostat

Opens

207°F - 217°F

(97°C - 103°C)

Heater Element

10 Ω - 40 Ω

120 V, 60 Hz

500 W Dry

N.C.

P4-1

P4-2

P4-3

P4-4

Electronic Control

N.O.

K504

Heater N Relay

(Also see Door

Switch Circuit)

Heater

BU/WH

BU/RD

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды